CA 1967 c20 parting out wiper arms

[sawman]

1967 chevy c20 cab for parts,alot of parts still on it inner fenders $175 offer,fuels tank and bolts,3 spd saginal transmission in very good condition,some of the floor,all firewall,inside heater box,heater controle with bezel needs 2 knobs all there and 3 cables,brake pedal, need something else off this cab front clip let me no.
wiper arms need blades and cleaning $42 shipped SOLD
c,sm back window glass is good,,need any part off this cab or cut off this cab let me no,all 4 sale IF ,still has the original small back glass in it,glove box door,fuel tank,brake pedal ect,grill inserts are 4 sale headlight bezels have dent as seen in pics,,wiper asm SOLD,wiper arms still for sale,hood latch Sold

will cut any part off thanks

[sawman]

any one see anything they need

[Ol 67 C10]

Any rust in the passenger fender or radiator support? If good, price shipped to VA 22830. Thanks

[sawman]

mild surface rust in spots,these are big items so shipping will be high with ups ground,make me a fair offer with shipping,

[sawman]

very hard to find solid cab,need any part cut off let me no,good cab corners,roof,floor on and on

[ScottH]

any arm rests or seat belts?

[sawman]

it both outer belts by edge of cab floor the plastic is in bad condition,it has the 2 metal/chrome fasterners that are bolted to the floor,

[sawman]

I have a set for bucket seats out of a 68 chevy van,

[burb71]

I need just the wiper linkage with clip still attached, I can't remember which link was on top or bottom, or the left from right.
And the hood latch with all it bolts.
Can you post more pic all around the cab it my be more small parts I can use.

Also please don't cut up a good rust free cab, at close to 50 years old its Gold
Sell it whole to somone!

[michael bustamante]

need the floor sections where it meets the kick panal on the driver side. from the seam at the firewall to 6' past the kick panal. also hows the headlight doors? any interior parts?

[sawman]

wiper asm sold to burb,still alot of parts

[sawman]

cab or cab parts still for sale

[1968k20]

I will take the glove box door please! I will look at other parts when you have time for me to come by.

[sawman]

glove box lid sold 68k20 pending payment

[sawman]

1968k20

[mjgord51]

I might be interested in the hole cab, D O N' T * C U T * T H E * C A B * U P . PM me with your location, Will you take 6 or 8 more pictures of the usual rot spots and then I'll make up my mind at that time, when you PM me I'll PM you back with my Email add. for you to send pic's. Marvin (mjgord)

[68Mike]

What's the condition of the front clip and is it complete? Hood, fenders, radiator support, grill

[67chevy4x4c]

Is the vent windows for sale and how much

[sawman]

no vent windows

[HONDAWASAKI]

Have an ash tray, and a driver side marker assy available? Also looking for a '67 steering wheel, armrests, and dash knobs. Thanks.

[Ol 67 C10]

I'd be interested in about a 10"x10" cutout where the studs for the gas pedal goes in the floorpan, if its good and if its still available. I can send pics of what I need. Shipping to 22830 VA. Thanks,Wes

[sawman]

yes its good ,please send pic were you want it cut,i can put that in a large flate rate box I think 16.50 shippingmake offer thanks ed

[Ol 67 C10]

I will get a pic and a measurement for you tomorrow. May be able to make it smaller and get it in a small flat rate box? Thanks, Wes

[Ol 67 C10]

Could you do $30 shipped? If so this is the piece that I need. I need the flange left on the front where it welds to the firewall and up on the first ledge where the trans tunnel is. Hopefully that makes since. Lol.

[sawman]

Ttt