|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
08-02-2015, 04:48 AM
|
#1 |
|
Registered User
Join Date: Jun 2015
Location: Reno
Posts: 34
|
What rear driveshaft will work for a Blazer?
Could I steal one from another 67-72, or are Blazers a different length. Or if anyone has one lying around they would be willing to part with?!! Thanks!
|
|
|
|
08-02-2015, 07:44 AM
|
#2 |
|
Registered User
Join Date: Dec 2008
Location: Clarkston, Michigan
Posts: 465
|
Re: What rear driveshaft will work for a Blazer?
I would have to say even though many parts from pickups to Blazers are interchangeable I will say the drive shaft won't fit only due to the fact its not the right length. U- joints are the same if its a 1/2 ton but that's it.
__________________
 Bought this thing bone stock with intentions to just add a lift and tires and the next thing I knew it was on my garage floor in a million pieces. Sometimes the best laid plans........
|
|
|
|
|
08-04-2015, 08:37 AM
|
#3 |
|
Registered User
Join Date: Sep 2013
Location: Bangor pa
Posts: 1,223
|
Re: What rear driveshaft will work for a Blazer?
Two and four wheel drives are different length. Most early Blazers up til 77-78 will be close to Same length and a 1310 u joint. Or you can have one built for a couple hundred. In a pinch you could take one from a pickup and cut it down and use it. Better to have a professional do that as well though.
__________________
72 3/4 ton blazer. 5 inch lift on 35 inch tires. 355 corvette engine with crane roller rockers, rv cam, edelbrock carb and intake with one inch spacer. Thrush Headers with flowmaster 40 duels. 4speed sm465 manual. 4 wheel disk brakes with Inboarded rear shock prerunner style mounts and shocks. |
|
|
|
|
08-04-2015, 09:47 AM
|
#4 |
|
Senior Member
 Join Date: May 2011
Location: Greencastle PA
Posts: 6,807
|
Re: What rear driveshaft will work for a Blazer?
I may have one laying around I will look tonight
|
|
|
|
|
08-05-2015, 11:25 AM
|
#5 |
|
Senior Member
Join Date: May 2011
Location: Greencastle PA
Posts: 6,807
|
Re: What rear driveshaft will work for a Blazer?
Probably will not be able to check until next week Sorry
|
|
|
|
|
08-09-2015, 08:09 PM
|
#6 |
|
Registered User
Join Date: May 2012
Location: Sanger, CA
Posts: 415
|
Re: What rear driveshaft will work for a Blazer?
If you have a local shop near you that builds custom drive lines check them out, they're are usually reasonable to have a new one built.
__________________
71 K5, AC/Tilt, 4" lift 33" tires 5.3L/4L60E/NP 205 (Under Construction) 05 Dodge 2500 4x4 5.9 Cummins (Daily driver) "Common sense is not so common" My build thread http://67-72chevytrucks.com/vboard/s...d.php?t=555879 |
|
|
|
|
08-10-2015, 04:29 PM
|
#7 |
|
Senior Member
Join Date: May 2011
Location: Greencastle PA
Posts: 6,807
|
Re: What rear driveshaft will work for a Blazer?
Sorry I don't have any that don't have some kind of issue with it
|
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
