Cup holders instead of seat belt holders - The 1947 - Present Chevrolet & GMC Truck Message Board Network

davepl · 01-07-2016, 04:43 PM

I've seen console reproductions with cup holders, but I'm wondering if my original console can accommodate cupholders instead of the belt holders. Someone on another thread said it was 2 screws, so that doesn't sound like it would be the whole top half.

What part of the console changes, and how invasive is it, and where do I get the cupholder part?

Thanks in advance for any info! I'm sure I'll make a lot more use out of cupholders than selt belt holders, especially since I have 3-pt retractables now.

**Already Gone** · 01-07-2016, 04:47 PM

subscribed

**FirstOwner69** · 01-07-2016, 05:21 PM

I've got a couple consoles of each type, but they're about 2000 miles away, so I can't compare them side by side.

If I recall correctly, the seat belt portion of the early consoles is integral (molded into) the top portion of the console. The cup holder portion of the later consoles is removable and held in place by 2 or 4 screws. You MAY be able to surgically remove the seat belt portion and add the cup holder portion, but I think some additional fabrication may be necessary to support the cup holder portion. Since the hinged tops and chrome trim rings are the same size, it's reasonable to assume the front section housing the cup holders would be the same size as the seat belt section.

I've seen billet cup holders to replace the factory cup holders, but I think you'd need to buy the factory cup holder section used.

Maybe someone would trade top sections with you. I know I would.

EDIT: Here's a link to a parts thread that has pictures of both types for comparison. http://67-72chevytrucks.com/vboard/s...hlight=console Also... the cup holder consoles use a different hinge for the lid.

Jim

frankslagoon · 01-07-2016, 05:55 PM

the console in my trk has cup holders. it sits in there with a couple screws. bad news is ya got to take the chrome strip off, which is doable but a little tricky. maybe the older consoles are one piece. All the blazer guys have these consoles. maybe check on the blazer forum.

67 chevelle · 01-07-2016, 06:14 PM

I used this
http://www.usa1industries.com/1967-8...r-console.html

lowrodderchev · 01-07-2016, 06:50 PM

Name: WP_20160107_14_49_25_Pro.jpg
Views: 616
Size: 26.9 KB

lowrodderchev · 01-07-2016, 06:46 PM

I cut my seatbelt console to use a cup holder drop in, its 2 screws

01-07-2016, 04:43 PM	#1
davepl Registered User Join Date: Aug 2006 Location: Redmond, WA Posts: 6,334	Cup holders instead of seat belt holders I've seen console reproductions with cup holders, but I'm wondering if my original console can accommodate cupholders instead of the belt holders. Someone on another thread said it was 2 screws, so that doesn't sound like it would be the whole top half. What part of the console changes, and how invasive is it, and where do I get the cupholder part? Thanks in advance for any info! I'm sure I'll make a lot more use out of cupholders than selt belt holders, especially since I have 3-pt retractables now. __________________ 1970 GMC Sierra Grande Custom Camper - Built, not Bought 1969 Pontiac 2+2 427/390 4-speed Coupe 1969 Pontiac 2+2 427/390 4-speed Convertible

01-07-2016, 04:47 PM	#2
Already Gone 70+ ( Old Skool Club ) Join Date: Nov 2003 Location: Saskatoon, Saskatchewan ,Canada Posts: 9,148	Re: Cup holders instead of seat belt holders subscribed __________________ 1972 C10 Custom/Deluxe 613 Highlander 406/700R4 1999 White Tahoe LS 4x2 with Z56 Police Package 1992 K1500 GMC Suburban Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601 " Circumsatances Do Not Change Responsibility " " The Sky is not the Limit, Your Mind is." Marilyn Monroe .. RIP Charlie Watts 1941 - 2021

01-07-2016, 05:21 PM	#3
FirstOwner69 Senior Member Join Date: May 2010 Location: Wisconsin & Arizona Posts: 4,853	Re: Cup holders instead of seat belt holders I've got a couple consoles of each type, but they're about 2000 miles away, so I can't compare them side by side. If I recall correctly, the seat belt portion of the early consoles is integral (molded into) the top portion of the console. The cup holder portion of the later consoles is removable and held in place by 2 or 4 screws. You MAY be able to surgically remove the seat belt portion and add the cup holder portion, but I think some additional fabrication may be necessary to support the cup holder portion. Since the hinged tops and chrome trim rings are the same size, it's reasonable to assume the front section housing the cup holders would be the same size as the seat belt section. I've seen billet cup holders to replace the factory cup holders, but I think you'd need to buy the factory cup holder section used. Maybe someone would trade top sections with you. I know I would. EDIT: Here's a link to a parts thread that has pictures of both types for comparison. http://67-72chevytrucks.com/vboard/s...hlight=console Also... the cup holder consoles use a different hinge for the lid. Jim Last edited by FirstOwner69; 01-07-2016 at 05:47 PM.

01-07-2016, 05:55 PM	#4
frankslagoon Registered User Join Date: Jan 2014 Location: Wasilla Alaska Posts: 537	Re: Cup holders instead of seat belt holders the console in my trk has cup holders. it sits in there with a couple screws. bad news is ya got to take the chrome strip off, which is doable but a little tricky. maybe the older consoles are one piece. All the blazer guys have these consoles. maybe check on the blazer forum.

01-07-2016, 06:14 PM	#5
67 chevelle Registered User Join Date: May 2013 Location: WEST PALM FLORIDA Posts: 1,174	Re: Cup holders instead of seat belt holders I used this http://www.usa1industries.com/1967-8...r-console.html __________________ 68 Long Fleet , ly6 , turbo 350 , 3-5 drop , original paint , front discs 67 Small window , 7 foot bed , tweaked 6.0 LSX 2004R Medium Olive 58 Apache fleet , 235 , offy intake , dual exhaust , 4 on the floor , red/white 69 Long Fleet , Custom , 6.0, 4l60 , AC , Medium Olive

01-07-2016, 06:50 PM	#6
lowrodderchev Registered User Join Date: Dec 2011 Location: visalia ca Posts: 1,480	Re: Cup holders instead of seat belt holders __________________ my 57 chevy truck build http://67-72chevytrucks.com/vboard/s...d.php?t=601554

01-07-2016, 06:46 PM	#7
lowrodderchev Registered User Join Date: Dec 2011 Location: visalia ca Posts: 1,480	Re: Cup holders instead of seat belt holders I cut my seatbelt console to use a cup holder drop in, its 2 screws __________________ my 57 chevy truck build http://67-72chevytrucks.com/vboard/s...d.php?t=601554



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.