![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Apr 2015
Location: East Tn (In the heart of the Smoky Mtns)
Posts: 1,870
|
String Alignment method
I finally got around to aligning the truck Before I take it to a shop.
I used the string method that was detailed here on another thread. It real easy to do. ![]() I had my son hold the steering wheel tight while I made the adjustments. I'm kinda curious how close I have it before putting it on a machine. |
![]() |
![]() |
![]() |
#2 |
Registered User
![]() Join Date: Sep 2008
Location: NEW MILFORD NJ
Posts: 1,453
|
Re: String Alignment method
after years of doing this stuff its a good way to get it close enough to safely drive to the front end shop but unless you have sliding plates under the wheels its hard to be accurate because the wheels will pull themselves to try to keep straight.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Apr 2015
Location: East Tn (In the heart of the Smoky Mtns)
Posts: 1,870
|
Re: String Alignment method
Yeah, I thought about that while adjusting the coolers, and had the son turn the wheel back and forth an then checked again. After getting the same measurements three times, I called it good. We'll see I guess
![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: May 2014
Location: PA
Posts: 1,417
|
Re: String Alignment method
Here in PA I'd never pay for an alignment. The roads are so bad it would be knocked out of alignment in no time. I just eyeball it and adjust after driving if it's twitchy.
__________________
1967 C10, LWB, 250, Powerglide, PS, PB, 3/4 STATIC DROP |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Apr 2011
Location: Fairview Park, Ohio
Posts: 1,031
|
Re: String Alignment method
Last time I did that the alignment shop said it was dead on
One this I did was drive the front tires onto a piece of scrap laminate, approx 10 x 12"Smooth side down then the tire doesn't bind on the concrete floor. A piece of sheet metal stock would prob also work.
__________________
My build page http://67-72chevytrucks.com/vboard/s...d.php?t=764662 My cabinet building site http://www.cbcabinets.com |
![]() |
![]() |
![]() |
#6 | |
Registered User
Join Date: Jul 2013
Location: LI, NY 11801
Posts: 1,140
|
Re: String Alignment method
Quote:
Cheap? Yes Efficient? Yes Major Score in my book!
__________________
1970 C10 8' Fleetside, L6 250, 3 on the Tree. The most basic of pickup trucks! |
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Apr 2015
Location: East Tn (In the heart of the Smoky Mtns)
Posts: 1,870
|
Re: String Alignment method
After reading this, I'm going to use the smooth surface method, and check it again. I have plenty of sheet metal that I can use.
|
![]() |
![]() |
![]() |
#8 |
Account Suspended
![]() Join Date: Jul 2016
Location: Tacoma, WA
Posts: 6,873
|
Re: String Alignment method
I just aligned mine on my smooth garage floor, to reduce tire friction I placed a double layer of plastic sheeting under each tire seemed like zero friction. I wired 1" square sticks to my rally wheels to measure toe in, drives great now
|
![]() |
![]() |
![]() |
Bookmarks |
|
|