![]() |
|
![]() |
#1 |
Pronounced "Pew-al-up"
Join Date: Oct 2002
Location: Puyallup, Washington
Posts: 845
|
gas guage reading
My gas guage when full reads 3/4 tank and when empty goes far below empty.
I know that we have 0-90 ohm sending units. Should it read 0 ohms at empty and 90 when full, or the other way around? Is there an easy way to calibrate the guage? Thanks, Dan
__________________
Classic GM Trucks of Washington Club Member 1970 FS chevy,350/350, Edelbrock cam and intake. Holley 650 carb,HEI,AT,Tangier Orange, 18's, Power Locks, Truck Photos |
![]() |
![]() |
![]() |
#2 |
Weapons Of Construction
Join Date: Apr 2000
Location: Colorado, USA
Posts: 1,095
|
If the wire is open, it goes waaay past full, so that would be the high (90 ohm) end of it.
When the wire is shorted to ground, it goes to E and that would be the 0 ohm end of it. I would suggest disconnecting the brown wire at your sending unit. If your guage goes way past full, the guage is probably alright. You might want to put in a 10 or 20 ohm resistor in series with your sending unit wire and see if that makes it work in the range you want. I don't know what currents are involved, but they should be fairly small to prevent fuel ignition (which would be bad). You can probably get away with a 1/4 watt resistor from Radio Shack, although a 1/2 watt would be easier to work with.
__________________
1971 GMC 2500, 402/TH400 4.10 Daily Driver Lafayette, CO |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Oct 2002
Location: West Des Moines, Ia
Posts: 3,233
|
i think you have a problem with your gauge mine was doing similar a while back but when full it was reading at 1/4 tank i tried everything, even bought a new sending unit and harness, but it came up to be the gauge.
__________________
Krazy Texan My Trucks are made with Wrenches not Chop Sticks 1967 GMC 3/4 ton "Johnny Cash" 1990 v1500 suburban 1967 Ford f100 Swb 4x4 "green bean" GOD BLESS JESUS, JOHN WAYNE, AND THE ALAMO |
![]() |
![]() |
![]() |
#4 |
Try spinnin 4 rear tars
Join Date: Sep 2003
Location: Salt Lake City, Utah
Posts: 757
|
71GMC_3/4T
OOOOoooo.... good call on the resistor!!!! I would go with the 1/2w resistor. I know that not alot of current goes through that wire, but better to have too much, than not enough.
__________________
SWEET7T 1970 C10, 2wd, LB, 307/TH350/3.08. PS, PB |
![]() |
![]() |
![]() |
#5 |
Pronounced "Pew-al-up"
Join Date: Oct 2002
Location: Puyallup, Washington
Posts: 845
|
Yeah I think that mine is the guage also. It didnt start happening until I installed a new bezel!!
Good advice on raising the resistance for the guage, I think I'll try it. I would like to keep everything to stock specs though. I will be installing an underbed tank someday!! Thanks for the great advice as usual!!! ![]()
__________________
Classic GM Trucks of Washington Club Member 1970 FS chevy,350/350, Edelbrock cam and intake. Holley 650 carb,HEI,AT,Tangier Orange, 18's, Power Locks, Truck Photos |
![]() |
![]() |
![]() |
Bookmarks |
|
|