Full Time Dana 60al

[IllinoisK30]

I just acquired a 1977 Chevy K30 SRW standard cab from Arizona. According to the info in the glove box it was originally bought in New Mexico and spent all of its life in Arizona, as far as I can tell it still retains the original 350 and is a factory 4-speed truck with 205 case. The body is very solid. The cab and frame are in great condition with very little outer cab corner work needing to be done. Front fenders and hood are junk. It must have sat under a pine tree at one time and the needles worked there way down to start the rotting process. This truck also came with factory bucket seats that I need to track down. Enough about the truck. I always thought that if the truck had a part time transfer case and manual trans it should have lockouts on the axle.
I bought it with some cheap lockouts on it but they did not work correctly and were very loose in the hub. I bought some original lockouts on eBay. I went to install them and there was no outer groove in the hub to hold the lockout body in the hub. It was smooth all the way out. I looked in my parts book and it did not show a locking hub break down for 77-78 trucks with Dana 60 just the full time drive gear and dust cap. I checked my later parts book and it shows the lockouts for the Dana 60's coming into view in 1979. I checked my '79 GMC and sure enough it had the groove at the outside of the hub for the snap ring.
Did 77-78 one ton trucks come with full time hubs regardless of wheather it was a manual or auto trans? Thanks for any help.
Posted via Mobile Device

[andyh1956]

I think your truck MAY have originally came with a NP 203 which might explain the hubs on the front.
Does the shift indicator plate on the trans hump have the correct pattern for your 205?

[IllinoisK30]

Originally Posted by andyh1956

I think your truck MAY have originally came with a NP 203 which might explain the hubs on the front.
Does the shift indicator plate on the trans hump have the correct pattern for your 205?

Posted via Mobile Device

[IllinoisK30]

Originally Posted by andyh1956

I think your truck MAY have originally came with a NP 203 which might explain the hubs on the front.
Does the shift indicator plate on the trans hump have the correct pattern for your 205?

The truck does have the correct plate with the 4L N 2H 4H on it. Correct round handle as well. Looks like it's been there from new. Nothing else on the truck throws up any red flags. I don't think it was swapped. I'm thinking that's the way it came?
Posted via Mobile Device

[cadillac_al]

Very interesting. It sounds like GM didn't have faith in any lockout hubs for a 1 ton truck in 77 and 78. I have never seen a 77 K30 in person so I always considered them kinda rare. I wonder what was holding your original cheap hubs in there?

[IllinoisK30]

Originally Posted by cadillac_al

Very interesting. It sounds like GM didn't have faith in any lockout hubs for a 1 ton truck in 77 and 78. I have never seen a 77 K30 in person so I always considered them kinda rare. I wonder what was holding your original cheap hubs in there?

I consider the 77 K30's rare because it is the first year for 4wd on a one ton chassis in that body style anyway. I have been looking for one for quite some time. I appreciate your reply. Here's some pictures.
Posted via Mobile Device

[Jeff's bowtie's]

Nice truck!! To bad your not close to Frederick Maryland there is a pair of Nos fenders and a nos pass door on Frederick Craigslist for $500.00 for the fenders and $300.00 for the door

[IllinoisK30]

Originally Posted by Jeff's bowtie's

Nice truck!! To bad your not close to Frederick Maryland there is a pair of Nos fenders and a nos pass door on Frederick Craigslist for $500.00 for the fenders and $300.00 for the door

Thanks Jeff, I do have two real nice GM fenders with the trim on them. One has the correct color molding on it the other is black. It's nice the holes are already there so no drilling. I will have to get the yellow paint matched as close as possible to paint all the black molding. The previous owner removed all the molding and sanded the truck into paint it back to original colors. When I bought it all the trim was missing including the tailgate band! I have an NOS door for the passenger side. Here's a picture of the SPID.
Posted via Mobile Device

[sweetk30]

i have a original 77k30 . 34k miles on it . i could go pull a full time drive slug cap and check for the grove for you tho .

easy to spot early trucks .

pass side king pin cap on dana 60 is cast iron NOT tin . first year or so only .

front spring hangers for rear springs were 2wd short . this gets you a factory 3" block WITH bump stop ear in the rear to make up the difference .

mine was a th400/203 truck and had a 2 piece drive shaft with carrier bearing . front shaft was around a foot or so . . .

if i recall been years but i do think they didnt have the grove . would be easy for someone to chuck up in a lathe and cut it in tho .

[Jeff's bowtie's]

I also have a pair of nos (no box) Silverado 30 fender emblems I bought here on the parts board awhile back I'd sell for what I paid for them

[IllinoisK30]

Originally Posted by Jeff's bowtie's

I also have a pair of nos (no box) Silverado 30 fender emblems I bought here on the parts board awhile back I'd sell for what I paid for them

Thanks for all the pictures. Looks to be in good shape. No dents or scratches? What are you asking for it? I just bought the fender name plates on a different sight. Probably paid to much. Let me know what your asking for those as well? May want an extra set. You can PM me if you rather.
Posted via Mobile Device

[Jeff's bowtie's]

It has two little scratches about the size of a dime and I don't know what you paid for your fender emblems but I paid $310.00 shipped I'd take $125.00 plus shipping for the tailgate band

[Jeff's bowtie's]

And the other

[IllinoisK30]

Originally Posted by Jeff's bowtie's

And the other

Sounds about right on the fender plates. I paid 300.00. I'll take the band for 125. Let me know what the total would be with shipping to 61038. Thanks.
Posted via Mobile Device

[Jeff's bowtie's]

Ok I'll get it boxed up and get you a total price shipped with insurance

[IllinoisK30]

Originally Posted by Jeff's bowtie's

Ok I'll get it boxed up and get you a total price shipped with insurance

Thank You.
Posted via Mobile Device

[Jeff's bowtie's]

Shipping would be $30.25 USPS priority sent you a pm thanks Jeff