Need advice installing stepside fenders - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dave6672** · 05-14-2018, 07:02 AM

I posted this in the paint and body section and got a couple of good responses, but thought I might get a few more here.........Soon I will be putting my newly painted step side fenders onto my newly painted bed sides. Question - what should I put, if anything, between the fenders and the bed where the fenders mount? I'm talking about the flange that is around the perimeter of the fenders where they make contact with the bed. Some type of seal or gasket? Seam sealer? Or just mount them up as is? Thanks!

Daves70 · 05-14-2018, 08:13 PM

Originally they were bolted on without anything between. The assembly manual says that there is a bead of sealer on the inside lip after assembly. I've seen some guys put a seal or welting between them.

**special-K** · 05-14-2018, 09:03 PM

I offer the same info. Basically, they are only virgin once...you repaint. Once installed that's it. I've seen a lot of trucks get the welting added, but not sure what help that does if any. It's really like any other two pieces of body bolted together.

**dave6672** · 05-17-2018, 07:03 AM

Thanks for the advice guys.

05-14-2018, 07:02 AM	#1
dave6672 Senior Member Join Date: Jul 2008 Location: Carrollton, KY Posts: 1,263	Need advice installing stepside fenders I posted this in the paint and body section and got a couple of good responses, but thought I might get a few more here.........Soon I will be putting my newly painted step side fenders onto my newly painted bed sides. Question - what should I put, if anything, between the fenders and the bed where the fenders mount? I'm talking about the flange that is around the perimeter of the fenders where they make contact with the bed. Some type of seal or gasket? Seam sealer? Or just mount them up as is? Thanks! __________________ Dave R. 1972 K20 1972 C20 Highlander 1967 C10

05-14-2018, 08:13 PM	#2
Daves70 Registered User Join Date: Jul 2011 Location: Mt Brydges Ontario Posts: 181	Re: Need advice installing stepside fenders Originally they were bolted on without anything between. The assembly manual says that there is a bead of sealer on the inside lip after assembly. I've seen some guys put a seal or welting between them.

05-14-2018, 09:03 PM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Need advice installing stepside fenders I offer the same info. Basically, they are only virgin once...you repaint. Once installed that's it. I've seen a lot of trucks get the welting added, but not sure what help that does if any. It's really like any other two pieces of body bolted together. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

05-17-2018, 07:03 AM	#4
dave6672 Senior Member Join Date: Jul 2008 Location: Carrollton, KY Posts: 1,263	Re: Need advice installing stepside fenders Thanks for the advice guys. __________________ Dave R. 1972 K20 1972 C20 Highlander 1967 C10



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.