New truck trying to figure out current suspension - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bmxbang · 09-11-2018, 08:09 PM

Alright guys I just purchased this 71 C-10 and Im trying to get some insight on what drop it may or may not have on it. The front spindles look factory but not sure on the springs. The shocks where replaced at some point in its life front and rear. Tire size on the wheels are 275/55/20. I don't currently have measurements from the ground to the fender so I will apologize for that because I know it would help. The bed is off a 63 but im sure you could tell that!

**AussieinNC** · 09-11-2018, 08:21 PM

4" front...4" rear

Front spindles most likely 2" drop plus 2" springs, would have needed new shocks
Rear springs look like 4 " drop, cant see the shocks so cant comment

How does it ride?
Bump Steer?
Bottom out?

bmxbang · 09-11-2018, 08:28 PM

Quote:

Originally Posted by AussieinNC

4" front...4" rear

Front spindles most likely 2" drop plus 2" springs, would have needed new shocks
Rear springs look like 4 " drop, cant see the shocks so cant comment

How does it ride?
Bump Steer?
Bottom out?

it honestly rides just fine does not bottom out from what little I have driven it. the front ball joints are shot. The spindles up front look pretty dang original from what I can tell. Thats lower than what I was hoping for.

**AussieinNC** · 09-11-2018, 08:33 PM

Sadly, there are some "mechanics" that will heat a set of coils to drop them, or worse, cut a coil or two off of them...

If the spindles look original, this may be the case...

Pics of front suspension showing coils and shocks will help...

Does it have a front sway bar fitted?

The way the 20's tuck up under the front fenders usually happens only with a 4" drop...

Check out this page on LMC site...it shows approx views of various drops..

http://www.lmctruck.com/icatalog/cb/full.aspx?Page=139

bmxbang · 09-11-2018, 08:41 PM

Deal I should have some time to pull off a wheel and post a picture up tomorrow and would love your insight! If I recall correctly I did not see a front sway bar. I appreciate the help man

**AussieinNC** · 09-11-2018, 08:44 PM

No worries mate !

bmxbang · 09-14-2018, 01:42 PM

the pictures where taking with the front end in the air also so the suspension was not compressed.

demian5 · 09-14-2018, 02:25 PM

Id say the rear is stock height with saggin springs.

Front maybe they cut a coil or 2.

**clay68c10** · 09-14-2018, 03:28 PM

Quote:

Originally Posted by demian5

Id say the rear is stock height with saggin springs.

Front maybe they cut a coil or 2.

x2

Those are stock front spindles also.

bmxbang · 09-14-2018, 03:44 PM

I was reallyyyy hoping it was mostly stock

I will be ordering a ECE 4/6 drop kit for it probably this winter and redoing the suspension. I just wanted to try and figure out how much more of a drop I could expect over what, if anything is on it now.

**clay68c10** · 09-14-2018, 06:14 PM

Here's some spindle pics I put up for comparison a while back.
http://67-72chevytrucks.com/vboard/s...d.php?t=763190

**Boog** · 09-15-2018, 05:25 AM

That's great Clay. It ought to be stickied at the top of the forum here and on the suspension forum if it isn't already. I saved it.

09-11-2018, 08:09 PM	#1
bmxbang Registered User Join Date: Aug 2018 Location: Blue Springs, MO Posts: 102	New truck trying to figure out current suspension Alright guys I just purchased this 71 C-10 and Im trying to get some insight on what drop it may or may not have on it. The front spindles look factory but not sure on the springs. The shocks where replaced at some point in its life front and rear. Tire size on the wheels are 275/55/20. I don't currently have measurements from the ground to the fender so I will apologize for that because I know it would help. The bed is off a 63 but im sure you could tell that! Attached Images Last edited by bmxbang; 09-14-2018 at 03:47 PM.

09-11-2018, 08:21 PM	#2
AussieinNC Moderator Join Date: Jun 2017 Location: Cherryville, NC Posts: 2,204	Re: New truck trying to figure out current suspension 4" front...4" rear Front spindles most likely 2" drop plus 2" springs, would have needed new shocks Rear springs look like 4 " drop, cant see the shocks so cant comment How does it ride? Bump Steer? Bottom out? __________________ Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox

09-11-2018, 08:33 PM	#4
AussieinNC Moderator Join Date: Jun 2017 Location: Cherryville, NC Posts: 2,204	Re: New truck trying to figure out current suspension Sadly, there are some "mechanics" that will heat a set of coils to drop them, or worse, cut a coil or two off of them... If the spindles look original, this may be the case... Pics of front suspension showing coils and shocks will help... Does it have a front sway bar fitted? The way the 20's tuck up under the front fenders usually happens only with a 4" drop... Check out this page on LMC site...it shows approx views of various drops.. http://www.lmctruck.com/icatalog/cb/full.aspx?Page=139 __________________ Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox

09-11-2018, 08:41 PM	#5
bmxbang Registered User Join Date: Aug 2018 Location: Blue Springs, MO Posts: 102	Re: New truck trying to figure out current suspension Deal I should have some time to pull off a wheel and post a picture up tomorrow and would love your insight! If I recall correctly I did not see a front sway bar. I appreciate the help man

09-11-2018, 08:44 PM	#6
AussieinNC Moderator Join Date: Jun 2017 Location: Cherryville, NC Posts: 2,204	Re: New truck trying to figure out current suspension No worries mate ! __________________ Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox

09-14-2018, 01:42 PM	#7
bmxbang Registered User Join Date: Aug 2018 Location: Blue Springs, MO Posts: 102	Re: New truck trying to figure out current suspension the pictures where taking with the front end in the air also so the suspension was not compressed.

09-14-2018, 02:25 PM	#8
demian5 Registered User Join Date: Aug 2016 Location: Lake Forest, CA Posts: 2,177	Re: New truck trying to figure out current suspension Id say the rear is stock height with saggin springs. Front maybe they cut a coil or 2. __________________ "Work hard, use your vacation days." 1970 C15 GMC Long Bed 1986 C20 Scottsdale 1983 K2500 Sierra Classic Suburban 6.2 Instagram: C10sofOC

09-14-2018, 03:44 PM	#10
bmxbang Registered User Join Date: Aug 2018 Location: Blue Springs, MO Posts: 102	Re: New truck trying to figure out current suspension I was reallyyyy hoping it was mostly stock I will be ordering a ECE 4/6 drop kit for it probably this winter and redoing the suspension. I just wanted to try and figure out how much more of a drop I could expect over what, if anything is on it now.

09-14-2018, 06:14 PM	#11
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,988	Re: New truck trying to figure out current suspension Here's some spindle pics I put up for comparison a while back. http://67-72chevytrucks.com/vboard/s...d.php?t=763190 __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

09-15-2018, 05:25 AM	#12
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,513	Re: New truck trying to figure out current suspension That's great Clay. It ought to be stickied at the top of the forum here and on the suspension forum if it isn't already. I saved it. __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.