![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jun 2018
Location: Texas
Posts: 1,353
|
Rockers install - On or Off the cab?
Is it ok to go ahead and install the rockers on my doors before I put the cab back on the frame? I have the cab sitting on jack stands under the cab frames right now. Does this matter?
If it does matter, what if I relocated the jack stands under the body mount holes and then installed the rockers? Or does it need to be on the frame? Thanks in advance.
__________________
TA_C10 Stage 1 build - http://67-72chevytrucks.com/vboard/s....php?p=8333444 "It's only money". ![]() |
![]() |
![]() |
![]() |
#2 | |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,487
|
Re: Rockers install - On or Off the cab?
Quote:
I would recommend on the frame with new cab mount bushings installed and bracing inside the cab. For bracing I use 3/4" conduit. LockDoc LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Jun 2018
Location: Texas
Posts: 1,353
|
Re: Rockers install - On or Off the cab?
Quote:
Thanks, Tom
__________________
TA_C10 Stage 1 build - http://67-72chevytrucks.com/vboard/s....php?p=8333444 "It's only money". ![]() |
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2017
Location: Semmes , AL
Posts: 45
|
Re: Rockers install - On or Off the cab?
Well the inner rocker is spot welded to the outer rocker ... So if you finish the bottom out in lizard skin , when you spot weld the two together your gonna burn through the undercoating ... I did my outer rockers off the frame , cab sitting on a wood frame I made that rolls ... I leveled it and sat it on the cab supports ... Hung my doors and installed my rockers ... Then laid cab on it back , on the wood frame , and finished the bottom and undercoated ... Then set it on the frame ... worked perfect and door gaps never moved ...
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2016
Location: Gallatin TN
Posts: 376
|
Re: Rockers install - On or Off the cab?
My floor, rockers, everything to the cab except final poly primer and final bodywork were done off the frame. I didn't have any issues, and nothing moves. Of course, for floor work, the cab was cross braced, but after the new floor went in, the bracing was removed.
No problem on mine anyway... |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2008
Location: Eastern Oregon
Posts: 2,336
|
Re: Rockers install - On or Off the cab?
Am I wrong ? I was told to remove doors to properly install new outer rockers.
__________________
71 C-20 07 Magnum RT AWD |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Feb 2017
Location: Semmes , AL
Posts: 45
|
Re: Rockers install - On or Off the cab?
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jul 2016
Location: Gallatin TN
Posts: 376
|
Re: Rockers install - On or Off the cab?
Could be I've been doing it wrong. I was taught to hang the doors prior to installation of outer rockers, as you actually use the door lines to line up the rockers. I was taught to do this on cars, and I see no reason why trucks are any different. Doors were hung, lined up with the body lines, prior to installation of the outer rockers. You do the same thing with a car body, even hang the doors prior to installation of 1/4 panels. You set the body lines of the doors to the original pieces, then leave the doors and line the new pieces up with the doors. Any welding/grinding fitment doesn't change because you "pin" the doors to the body (drill holes and use alignment pins) so everything goes back exactly after paint...
At least, that's how I was instructed to do it... |
![]() |
![]() |
![]() |
#9 |
Moderator
![]() Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,193
|
Re: Rockers install - On or Off the cab?
Maybe I am just old fashioned...
Any cab repairs I perform are always off chassis and on my jig.... The jig I built mirrors the factory frame dimensions and drops.... It also has adjustable spreaders to allow setting the door opening width to spec...and match side to side....it also allows the doors to be mounted and aligned and locked in place to allow accurate placement of the rockers...doors should be in place to ensure accurate body lines...and to ensure the doors can close!!!! (Fixed two cabs in last few months because the doors would catch on the rockers!!!) I always check door gaps before I start any body repairs ....however the exercise becomes a waste of time if the cab supports are shot...as the cab will twist throwing off the body lines... Check cab supports for both rot and collapse of the rubber supports.... Check floor pan area especially where firewall meets floor pan for rot... If the cab has bad cab supports and bad floor pan where it meets the firewall...the cab gets a full new floor ! Yep, I know its more money...but a huge saving in time and you know its going to line up right.... Check lower A pillar areas for rot especially inside where vent panels opening is located...repair panels are available but must be accurately replaced. Check upper windshield internal area for rot...repair panels are available but must be accurately replaced. Check bottoms of doors for rot...repair panels are available but must be accurately replaced. Check door hinge mount plate areas for cracks...(common) Check vent window cross piece between inner and outer panels for cracks (common)... Hope this helps.... ![]() ![]() ![]()
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jun 2018
Location: Texas
Posts: 1,353
|
Re: Rockers install - On or Off the cab?
Thanks all for the great info. Check back soon on my build thread below as I am posting all my work with pics. I may or may not build a 4x4 frame to support. I have a jig I built to pick the cab up with my cherry picker so it may just be easier to just sit the cab back on the frame rather than build another frame... Either way looks like I will be ok.
I plan to mount the doors as I do each rocker to make sure my gaps are correct, tack a few spots to hold the rockers and then remove the door and finish up the welds. By doing this I believe it will benefit me to measure from the floor up to the door body lines to try and get the doors nice and level so when I put the fenders and bed on they will all match up nicely and minimize any kind of slant I may create. But centering the doors in the cab should be enough actually...
__________________
TA_C10 Stage 1 build - http://67-72chevytrucks.com/vboard/s....php?p=8333444 "It's only money". ![]() |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Apr 2018
Location: Sabattus, maine
Posts: 209
|
Re: Rockers install - On or Off the cab?
I installed my rockers while my cab was on jack stands, I leveled the cab, put the door on set the gaps, marked the cab, then removed the door and went to town.. better pics in my build thread.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|