In stumped. Not easy to do. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72c20customcamper · 02-27-2019, 04:57 PM

I just cleaned out the 68's gas tank ..lots of crap but this is perplexing. A few large clumps of non metallic crap. Could it be the remnants of the copper float. Nuts were shiney when put in the tank.

72c20customcamper · 02-27-2019, 05:00 PM

Tank came out great

**Steeveedee** · 02-27-2019, 05:48 PM

No idea on the gunk. Are you going to use a sealer to coat the inside of the tank?

morepwr · 02-27-2019, 06:58 PM

Maybe the remnants of a sock for the fuel pick up?

jamyers · 02-27-2019, 07:22 PM

With the gas caps located so conveniently, there is absolutely no telling. Kids dropping rocks, toys, cat poop (yup) in these old fuel tanks isn't rare at all.

I'd go one further, and put a double handfull of small screws, nuts and bolts and some ATF in there, hang the tank from a rope at it's balance point, then slosh everything back and forth. The smaller hardware will get into the corners better than mid-size nuts, and ATF is a decent cleaner.

72c20customcamper · 02-27-2019, 09:10 PM

I used phosphorus acid to get the rust out with the nuts to agitate it. Should have a nice phosfate coating on the tank. Not going to coat it.

**jocko** · 02-27-2019, 09:30 PM

It could be MY old socks, I have a few solo artists arcin around here...

Just my 2c, but while you've gone to the trouble to clean it, the inner coating goes a long way to keeping ANYthing that didn't get flushed from coming loose and clogging the new filter sock. it will take time to clog, but it would take a lot longer to clog with an inner seal coat - and they are very easy to apply, much less work than the cleaners, assuming you still have the tank out (pour in, roll over a time or two, let dry, repeat and let dry lying on the other big side the 2nd time for a pretty even inner coat). I recently did this to my 59 MF50 tractor's tank and it seemed to make quite a clean surface that sealed in all the crap that looked like it could come loose over time after I cleaned it and before I coated it. Just a thought, either way, BIG improvement. I guess I'll throw away one of my mis-matched socks now.

**special-K** · 02-27-2019, 10:51 PM

I think Joe Dirt figured it all out for us. It's space poopy

72c20customcamper · 02-28-2019, 08:17 PM

Well its definitely organic. Dissolves completely in water. Had to rinse the tank 6 times with hot water. Phosphate coating held up no flash rust. Nothing in there anymore. I did flush it with isopropyl alcohol to dry it out .

02-27-2019, 04:57 PM	#1
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,635	In stumped. Not easy to do. I just cleaned out the 68's gas tank ..lots of crap but this is perplexing. A few large clumps of non metallic crap. Could it be the remnants of the copper float. Nuts were shiney when put in the tank. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

02-27-2019, 05:00 PM	#2
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,635	Re: In stumped. Not easy to do. Tank came out great Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

02-27-2019, 05:48 PM	#3
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,592	Re: In stumped. Not easy to do. No idea on the gunk. Are you going to use a sealer to coat the inside of the tank? __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

02-27-2019, 06:58 PM	#4
morepwr Registered User Join Date: Jun 2018 Location: Ventura, Ca Posts: 206	Re: In stumped. Not easy to do. Maybe the remnants of a sock for the fuel pick up? __________________

02-27-2019, 07:22 PM	#5
jamyers Registered User Join Date: Jan 2013 Location: Buffalo Gap, TX Posts: 229	Re: In stumped. Not easy to do. With the gas caps located so conveniently, there is absolutely no telling. Kids dropping rocks, toys, cat poop (yup) in these old fuel tanks isn't rare at all. I'd go one further, and put a double handfull of small screws, nuts and bolts and some ATF in there, hang the tank from a rope at it's balance point, then slosh everything back and forth. The smaller hardware will get into the corners better than mid-size nuts, and ATF is a decent cleaner. __________________ My Chevy Truck Project Build Thread '62 Ranchero - 200 I6, 3-on-the-tree, power nothing. '71 LeSabre - 455 Stage 1, power everything.

02-27-2019, 09:10 PM	#6
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,635	Re: In stumped. Not easy to do. I used phosphorus acid to get the rust out with the nuts to agitate it. Should have a nice phosfate coating on the tank. Not going to coat it. __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

02-27-2019, 09:30 PM	#7
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,976	Re: In stumped. Not easy to do. It could be MY old socks, I have a few solo artists arcin around here... Just my 2c, but while you've gone to the trouble to clean it, the inner coating goes a long way to keeping ANYthing that didn't get flushed from coming loose and clogging the new filter sock. it will take time to clog, but it would take a lot longer to clog with an inner seal coat - and they are very easy to apply, much less work than the cleaners, assuming you still have the tank out (pour in, roll over a time or two, let dry, repeat and let dry lying on the other big side the 2nd time for a pretty even inner coat). I recently did this to my 59 MF50 tractor's tank and it seemed to make quite a clean surface that sealed in all the crap that looked like it could come loose over time after I cleaned it and before I coated it. Just a thought, either way, BIG improvement. I guess I'll throw away one of my mis-matched socks now.

02-27-2019, 10:51 PM	#8
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,852	Re: In stumped. Not easy to do. I think Joe Dirt figured it all out for us. It's space poopy __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

02-28-2019, 08:17 PM	#9
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,635	Re: In stumped. Not easy to do. Well its definitely organic. Dissolves completely in water. Had to rinse the tank 6 times with hot water. Phosphate coating held up no flash rust. Nothing in there anymore. I did flush it with isopropyl alcohol to dry it out . __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.