WA NL2 auxiliary fuel tank parts

[randy500]

Wiring harness, modified for toggle switch $30 shipped
Fuel filler cover, little rust at the bottom $45 shipped...Sold
Fuel filler neck with original gas cap, $50 shipped
Wiring harness with factory switch, $75 shipped...Sold
Valves with plastic bolt spacers, $30ea shipped
Plastic trim plate, one small crack, $35 shipped...Sold

Combined shipping discount could be huge....

[DeadheadNM]

Interested in the oem harness/oem switch - working switch? Knob and bezel included?

Also interested in the trim plate pending pics.

Thanks.

[randy500]

I opened up the switch, cleaned it to bright copper contacts, lubed with white lithium grease and close dit up, works great now.
Wiring harness has cut on grommet where someone ran a wire, still has crimped on wire protector at tank, i had to pull the wire out of the ring terminal to remove it, the nut was too rusty to remove.

The other wore harness the grommet is not cut, you could crimp on some packard terminals and insert the wires into the plastic switch connector

[randy500]

Harness grommet cut

[randy500]

Other harness

[randy500]

Filler neck cover

[randy500]

Filler neck with original fuel cap.

[chewychevy67]

Is this off a 72? Would it be a vented cap? I would be interested in all the fuel filler pieces and if possible Maby the cutouts around box where the filler goes thru. I need a vented system for a 67 though.

[randy500]

Originally Posted by chewychevy67

Is this off a 72? Would it be a vented cap? I would be interested in all the fuel filler pieces and if possible Maby the cutouts around box where the filler goes thru. I need a vented system for a 67 though.

It is a 72, The cap is standard 72 eec type (smaller opening) so im sure its vented. These k20’s have the older large opening non eec cap on the cab tank and the smaller opening cap on the aux tank. Kind odd i think.

I can cut the bed for templates from my 72 chev k20 with NL2, $30 for the cut plus whatever shipping is...do you have a US shipping address?

[DeadheadNM]

Thanks Randy. I’ll take the plate.

If no takers for the harness with the switch I would take just the switch.

[randy500]

Originally Posted by DeadheadNM

Thanks Randy. I’ll take the plate.

If no takers for the harness with the switch I would take just the switch.

I can do $80 shipped on the switch and plate if that works for you.

[DeadheadNM]

Originally Posted by randy500

I can do $80 shipped on the switch and plate if that works for you.

Sounds good thanks. I’ll take it and send balance here ASAP.

[randy500]

Originally Posted by DeadheadNM

Sounds good thanks. I’ll take it and send balance here ASAP.

I got the money Pete, its packaged up, will print a label later and send tracking, thank you.

I see now....your sending the remainder for the switch too....i will get it re packaged for you.

[DeadheadNM]

Originally Posted by randy500

I got the money Pete, its packaged up, will print a label later and send tracking, thank you.

I see now....your sending the remainder for the switch too....i will get it re packaged for you.

Yessir. Just sent the balance. Thanks again.

[chewychevy67]

I do have a US address. So this would use the same fuel grommet and fuel cap as the 67 70 trucks? Could you get me a few more pictures of this setup?

[randy500]

Originally Posted by chewychevy67

I do have a US address. So this would use the same fuel grommet and fuel cap as the 67 70 trucks? Could you get me a few more pictures of this setup?

Any specific pictures needed? The grommet looks similar to the earlier tank grommet, i dont know if its the same or not.
The fuel cap is 72. Pictures coming.

[chewychevy67]

Nothing specific. It has a vent tube for filling correct? I can't see it in the picture. Just want to make sure I can use these for what I'm trying to do.

[randy500]

More pics, you would get the bed cut from the green truck.
The filler neck has an overflow tube, the tank would have the vent tube.
Same as any...the vents are always in the tanks.

[randy500]

Another picture

[chewychevy67]

Thanks for the pics. I am going to pass at this moment as I might try doing something more like the burbs have.

[karphan]

I will take the fuel filler neck. PM sent. Thanks, Dan

[randy500]

Originally Posted by karphan

I will take the fuel filler neck. PM sent. Thanks, Dan

PM replied, money recieved, i need your address......I see your address via PM, thank you.

[karphan]

Excellent! Thank you! Dan

[randy500]

Ttt

[randy500]

Ttt