55.2-59 FI and new engine - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Rickysnickers** · 11-27-2019, 11:36 AM

I purchased a Pro Flo 4 kit a while back. I got it all installed with a new engine. I just have to prime the oiling system and then make sure the distributor is installed correctly. I did make sure there were no leaks in the fuel lines, so I'm good there as the fuel pump was whining as it ran to pump gas through the lines. The gauge showed 58psi, perfect! I'm honestly a little scared to start it though....

**mr48chev** · 11-27-2019, 03:17 PM

Sounds like some excitement is about to happen.

**Rickysnickers** · 11-27-2019, 04:06 PM

Quote:

Originally Posted by mr48chev

Sounds like some excitement is about to happen.

Well yes. I'm just nervous about getting the distributor set correctly. I did as the fuel injection instructions said and set it 12 degrees BTDC. Still, I'm concerned that I might screw it up. Any advice for double checking that I'm on the correct stroke?

dsraven · 11-27-2019, 08:50 PM

set it for the tdc mark, pull number one spark plug and see if you can blow compressed air into the cylinder and have it hold or if it leaks out past the valves. be careful doing this as it tends to rotate the engine if you pressure it up too much. it is basically a cyl leak down test. otherwise, pull a valve cover, watch the rockers as you rotate the engine, and deal with leaky gasket after.

dsraven · 11-27-2019, 08:58 PM

if you just want to test fire it, disable the fuel pump, squirt a little gas down the intake, install the air filter again in case it pops back through the intake when you try to start it. now crank it over and see if it tries to start or if it pops back. if it tries to start then it is probably set up ok for tdc on "ready to fire" stroke. if confident that is the case then connect the fuel pump and try it again, it'll probably fire up. install a timing light and adjust timing to be close enough to break it in. follow the recommended break in procedure from the manufacturer of the engine and document as req for warranty purposes.

11-27-2019, 11:36 AM	#1
Rickysnickers Senior Member Join Date: Oct 2014 Location: Eagle, ID Posts: 3,058	FI and new engine I purchased a Pro Flo 4 kit a while back. I got it all installed with a new engine. I just have to prime the oiling system and then make sure the distributor is installed correctly. I did make sure there were no leaks in the fuel lines, so I'm good there as the fuel pump was whining as it ran to pump gas through the lines. The gauge showed 58psi, perfect! I'm honestly a little scared to start it though....

11-27-2019, 03:17 PM	#2
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,705	Re: FI and new engine Sounds like some excitement is about to happen. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

11-27-2019, 08:50 PM	#4
dsraven Registered User Join Date: Nov 2010 Location: calgary alberta Posts: 8,323	Re: FI and new engine set it for the tdc mark, pull number one spark plug and see if you can blow compressed air into the cylinder and have it hold or if it leaks out past the valves. be careful doing this as it tends to rotate the engine if you pressure it up too much. it is basically a cyl leak down test. otherwise, pull a valve cover, watch the rockers as you rotate the engine, and deal with leaky gasket after.

11-27-2019, 08:58 PM	#5
dsraven Registered User Join Date: Nov 2010 Location: calgary alberta Posts: 8,323	Re: FI and new engine if you just want to test fire it, disable the fuel pump, squirt a little gas down the intake, install the air filter again in case it pops back through the intake when you try to start it. now crank it over and see if it tries to start or if it pops back. if it tries to start then it is probably set up ok for tdc on "ready to fire" stroke. if confident that is the case then connect the fuel pump and try it again, it'll probably fire up. install a timing light and adjust timing to be close enough to break it in. follow the recommended break in procedure from the manufacturer of the engine and document as req for warranty purposes.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.