|
09-02-2020, 04:38 PM | #1 |
Registered User
Join Date: Dec 2018
Location: Dallas, PA
Posts: 551
|
Seat belt bolts
What size are the bolts for the seatbelts, that attach to the factory holes in the floor ?
|
09-02-2020, 05:43 PM | #2 |
Registered User
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 2,235
|
Re: Seat belt bolts
DOT requires 7/16" UNF, or 1/2" UNC.
__________________
1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate |
09-02-2020, 07:19 PM | #3 | |
Moderator
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: Seat belt bolts
Quote:
I just looked at an old thread I posted and the stock holes I have are 7/16" fine thread. http://67-72chevytrucks.com/vboard/s...7&postcount=11 This is the type of bolts you use. Don't cheap out - https://www.julianos.com/Grade-8-7-1...p/ju010100.htm https://www.classicindustries.com/pr...oaAncvEALw_wcB https://www.opgi.com/interior-access...d-plated-1-14-
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? Last edited by The Rocknrod; 09-02-2020 at 07:35 PM. |
|
09-02-2020, 09:40 PM | #4 |
Registered User
Join Date: Oct 2012
Location: Philly, PA
Posts: 539
|
Re: Seat belt bolts
Apologizes for going OSHA, but can't over emphasize that the big @ss washer in Rocknrod's 1st link is what keeps the bolt from pulling through the floor should the vehicle comes to a violent stop. It takes little force to pull a single bolt head through sheet metal upon impact, so think of that washer as life insurance.
__________________
My truck ain't dead, it just smells funny. |
09-03-2020, 08:33 AM | #5 | |
Registered User
Join Date: Dec 2018
Location: Dallas, PA
Posts: 551
|
Re: Seat belt bolts
Quote:
My truck has the factory threaded holes in the floor, do I need nuts & washers under the truck floor as well ? |
|
09-03-2020, 12:58 AM | #6 |
Registered User
Join Date: Feb 2013
Location: central California
Posts: 2,744
|
Re: Seat belt bolts
Just to add to ACK's point about using big arse washers when not using factory holes...Juliano's has an answer for that and I use them
https://www.julianos.com/Juliano-s-A...p/ju010600.htm |
09-03-2020, 09:31 AM | #7 |
Registered User
Join Date: Feb 2013
Location: central California
Posts: 2,744
|
Re: Seat belt bolts
No, factory holes are used with the bolts like Rocknrod posted.
|
09-03-2020, 09:59 AM | #8 |
Registered User
Join Date: Dec 2018
Location: Dallas, PA
Posts: 551
|
Re: Seat belt bolts
|
09-03-2020, 10:21 AM | #9 |
Moderator
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: Seat belt bolts
Just to be clear they're called "shoulder bolts" because of the un-threaded larger shoulder below the hex hex. Not because they are used just on shoulder belts.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
09-03-2020, 10:05 AM | #10 |
Registered User
Join Date: Feb 2013
Location: central California
Posts: 2,744
|
Re: Seat belt bolts
My '66 had factory lap belts which were anchored with a shouldered bolt like the pic. That way the belt anchors could swivel a bit on the bolts. I personally would just go down to the hardware store and get a grade 8 bolt that fits and cinch them down tightly.
Last edited by AcampoDave; 09-03-2020 at 10:11 AM. |
09-03-2020, 05:19 PM | #11 |
Registered User
Join Date: Oct 2012
Location: Philly, PA
Posts: 539
|
Re: Seat belt bolts
In short, if there's an anchor plate under the truck, most likely a rectangular piece of thick stamped sheet metal with a nut welded in the middle, you should look for 7/16"-20 x 1.25" bolts as mentioned above. As a side, the '64 - '66 shop manuals don't mention seat belts at all, however, I'm quite sure the assembly manual does. I agree with AcampoDave, grade 8 bolts are the way to go.
__________________
My truck ain't dead, it just smells funny. |
Bookmarks |
|
|