Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
12-07-2020, 06:20 PM | #1 |
Registered User
Join Date: Sep 2017
Location: Sunny CA
Posts: 59
|
Engine block identification help
So... I posted a week ago or so about the little hex head screw port above the water pump, and someone said it could be an oil pressure sending port, found on a non-350 engine.
So it got me to wondering... what if this wasn't a 350? would I know? probably not... I had checked the number on the back near the bellhousing (3970010) and one site says 350 for sure (this was why i assumed a 350), another says possible 327 from a car. The front numbers are not easily visible, but after some scraping it looks like the one says "017CKD" (or at least that's what i think it says). The other has a few missing numbers/letters, but what is visible shows "13**38409" (* = unreadable). There may be an extra * in there... The digits are not part of the truck's VIN so I am sure this is not the original engine (and was told it was a crate 350). It did have Targetmaster 350 valve covers, but from what I could find, one of these numbers would have a "CE" to indicate a crate engine... Anyone who can help ID this thing? Everything I could find says there should be a letter or more digits prior to "017CKD", but it really doesn't look like it was there... |
12-07-2020, 06:39 PM | #2 |
Registered User
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
|
Re: Engine block identification help
Almost certainly a 350
A few will be 327 Only way to check pull oil pan many find casting numbers on the crank Yes it could have been a crate motor in the 70s and could have a truck 327 crank stuck in it as well |
12-07-2020, 09:55 PM | #3 |
Who Changed This?
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,516
|
Re: Engine block identification help
If you have a head off, or plan on taking them off, you can measure the bore and stroke that way.
__________________
~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA |
12-07-2020, 09:59 PM | #4 |
Registered User
Join Date: Jan 2003
Location: Safford,AZ
Posts: 3,612
|
Re: Engine block identification help
Looks to be a 1973 350
|
12-09-2020, 12:19 AM | #5 |
Registered User
Join Date: Oct 2013
Location: CT.
Posts: 260
|
Re: Engine block identification help
Hello, that is a oil passage hole. When I ran boats with timeing gears in them I would weld a fitting into the cover and use that as an oil feed to the gear set due to the angle of the inboard engine.
|
12-09-2020, 12:56 AM | #6 |
Registered User
Join Date: Jul 2009
Location: Space Coast, Fl.
Posts: 1,050
|
Re: Engine block identification help
looks like all 4brl. carb... no indication of 2 or 4 bolt main
CKD 1972 350 175 4 tur hydro trans CKD 1973 350 200 4 tur hydro, Calif CKD 1974 350 160 4 T350 NB2 CKD 1977 350 180 4 a/t, high altitude http://chevy-camaro.com/chevy-camaro...es.php?group=2
__________________
Dad always said, "Son, WISH IN ONE HAND, and ......." -------------------------------------- -------------------------------------- Current toy trucks: '71 GMC 1500 SUPER CUSTOM short/step, orig. dk. blue, 350/700r, ps,pb, A/C '72 Blazer 2wd, ochre & white, 454, tremecTKO 500 5spd. ps, pb, A/C, tilt Last 10yrs of hobby vehicles, had a FEW more in the 50yrs. before these: '66 Plymouth Belvedere City of Miami cop car clone. '70 Nova 406"sb, 13.5-1, solid roller, Brodix, p.glide/t.brake, back halved, 9" Ford, spool 4.88, cage,ladder bar/coilover, 10.5 tire....... SOLD!! '67 C10 short/step side mount spare -- SOLD!! '72 Jimmy 2wd, 350/350, ps, pb, fun driver, lots of bondo & a shiny red paint job..... SOLD!! '69 Nova 350, 4spd, A/C, ps, p.b, ...SOLD!! |
12-09-2020, 12:57 PM | #7 | |
Registered User
Join Date: Sep 2017
Location: Sunny CA
Posts: 59
|
Re: Engine block identification help
Quote:
|
|
12-09-2020, 12:59 PM | #8 |
Registered User
Join Date: Sep 2017
Location: Sunny CA
Posts: 59
|
Re: Engine block identification help
|
12-09-2020, 04:50 PM | #9 |
All about them Ks
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,417
|
Re: Engine block identification help
Doubt it, my K20 has a 350 from a 73 C20 in it that has that plugged hole. Old school racers used to use them as mentioned to lube the timing sets.
__________________
Tyler '57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888 '72 K20 Cheyenne: 5 lift, 35s, front dana 60 blah blah blah http://67-72chevytrucks.com/vboard/s...d.php?t=662879 69 K10 SWB: 4 lift 33s in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206 '98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20s |
12-10-2020, 02:05 PM | #10 |
Registered User
Join Date: May 2009
Location: Canton, Tx
Posts: 175
|
Re: Engine block identification help
i have Seen the Plug on many 350's it is part of the oiling system and I have always been told if it had that Plug it was a 4 bolt Main engine. No positive but every one I have seen has been 4 bolt main and I have never seen a 4 bolt main without the plug.
|
12-09-2020, 04:37 PM | #11 |
Registered User
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
|
Re: Engine block identification help
I have seen that plug on several blocks I live in an area marine blocks are highly unlikely
3970010....302.....69....4...Z-28 Camaro 3970010....327.....69....2...Trucks and industrial 3970010....350...69-80...2 or 4 Because they used it in 3 main different configurations have to look at the crank and it was 2 or 4 bolt main block only way to tell is pull the oil pan http://chevellestuff.net/qd/crank/crank.htm |
12-10-2020, 05:29 PM | #12 |
Registered User
Join Date: Sep 2017
Location: Sunny CA
Posts: 59
|
Re: Engine block identification help
Well I am not going to pull the pan soon, but I know the clutch will need replacing in the distant future... good excuse to pull the engine and work on it outside of the truck... I will assume 350 until I pull the pan.
Just to clarify, if there is a 4 bolt main, it must be a 350 because GM didn't make a 4 bolt 327? |
12-10-2020, 10:45 PM | #13 |
All about them Ks
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,417
|
Re: Engine block identification help
Correct, some guys will fight you tooth and nail but GM never built a factory 4 bolt 327, only small and large journal 2 bolts.
For what it’s worth my 350 with said plugged oil galley hole is a 4 bolt block.
__________________
Tyler '57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888 '72 K20 Cheyenne: 5 lift, 35s, front dana 60 blah blah blah http://67-72chevytrucks.com/vboard/s...d.php?t=662879 69 K10 SWB: 4 lift 33s in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206 '98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20s |
Bookmarks |
|
|