The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-07-2021, 05:49 PM   #1
Gigem
Registered User
 
Gigem's Avatar
 
Join Date: Feb 2012
Location: Lakeway, TX
Posts: 335
Yet another window seal, fuzzy, belltline, etc. thread

I have searched and ready plenty of threads on this topic, but I still don't have a decision on the best solution here.

I have removed the inner and outer window seals on my 72 GMC, and want to replace with something new.

I honestly don't care if they aren't 100% waterproof "squeegee" action, as this is a fair weather only truck. I just want them to fit right, look decent and help keep the window from rattling around.

Everyone complains about the ones from LMC, which I gather are made by Precision. A set of these (two inners and outers) costs $30 so I am not surprised that they suck.

I saw a thread where a guy used some that were glued on. He says they have held up but I don't like the idea of gluing them on and they didn't look anything like original to me. Glue was the biggest concern. These were like $50 and were just outers. I guess you use the Precision inners...

I have had decent luck with Steele stuff, and they show a set of these (oddly they only show for a Chevy, not a GMC) for the princely sum of $100.

https://www.steelerubber.com/window-...rip-80-0060-57

Has anyone used these Steele ones?

I really don't want to spend $100 here, but I guess I will if they are really good.

Thanks.
__________________
1972 GMC Sierra Grande (current truck)
1980 Chevy Stepside (gone)
1987 Chevy Blazer (gone)
1972 Chevelle SS Convertible (gone)
1973 Chevy Corvette (gone)
1967 Chevy Camaro (STOLEN!)
Gigem is offline   Reply With Quote
Old 02-07-2021, 09:11 PM   #2
03BlkZ
Registered User
 
Join Date: Nov 2015
Location: Hewitt, Tx
Posts: 386
Re: Yet another window seal, fuzzy, belltline, etc. thread

Quote:
Originally Posted by Gigem View Post
I have searched and ready plenty of threads on this topic, but I still don't have a decision on the best solution here.

I have removed the inner and outer window seals on my 72 GMC, and want to replace with something new.

I honestly don't care if they aren't 100% waterproof "squeegee" action, as this is a fair weather only truck. I just want them to fit right, look decent and help keep the window from rattling around.

Everyone complains about the ones from LMC, which I gather are made by Precision. A set of these (two inners and outers) costs $30 so I am not surprised that they suck.

I saw a thread where a guy used some that were glued on. He says they have held up but I don't like the idea of gluing them on and they didn't look anything like original to me. Glue was the biggest concern. These were like $50 and were just outers. I guess you use the Precision inners...

I have had decent luck with Steele stuff, and they show a set of these (oddly they only show for a Chevy, not a GMC) for the princely sum of $100.

https://www.steelerubber.com/window-...rip-80-0060-57

Has anyone used these Steele ones?

I really don't want to spend $100 here, but I guess I will if they are really good.

Thanks.
I ordered some from Steele rubber about a month ago and still have not received them. I actually called on Friday and the said they will reach out to the vendor and have an answer Monday. Steele has been good so far on other things. I made a poor judgment call and ordered som seals and other rubber things from LMC and they were terrible. The door seals would not even allow me to close the doors. They were way too big and too stiff. Steele seals were perfect so that's why I went back to them for the window felt.
03BlkZ is offline   Reply With Quote
Old 02-07-2021, 09:12 PM   #3
03BlkZ
Registered User
 
Join Date: Nov 2015
Location: Hewitt, Tx
Posts: 386
Re: Yet another window seal, fuzzy, belltline, etc. thread

I ordered some from Steele rubber about a month ago and still have not received them. I actually called on Friday and the said they will reach out to the vendor and have an answer Monday. Steele has been good so far on other things. I made a poor judgment call and ordered som seals and other rubber things from LMC and they were terrible. The door seals would not even allow me to close the doors. They were way too big and too stiff. Steele seals were perfect so that's why I went back to them for the window felt.
03BlkZ is offline   Reply With Quote
Old 02-07-2021, 11:41 PM   #4
cj847
Registered User
 
cj847's Avatar
 
Join Date: Sep 2016
Location: Ozark, MO
Posts: 567
Talking Re: Yet another window seal, fuzzy, belltline, etc. thread

I haven't bought from LMC so I can't comment. I did install a set from classic parts of America and they are fine. I did have to trim them a little, but i would expect that from any vendor. Can't comment on longevity as they are only 5-6 mos old. I don't believe that these seals are meant to do as much as some expect out of them. The weep holes in the bottom of the door are there for a reason......

https://www.classicparts.com/1967-72...ctinfo/03-571/
cj847 is offline   Reply With Quote
Old 02-08-2021, 11:20 AM   #5
72bowtiestepper
Registered User
 
Join Date: Feb 2013
Location: Northwest NJ
Posts: 684
Re: Yet another window seal, fuzzy, belltline, etc. thread

Quote:
Originally Posted by cj847 View Post
I haven't bought from LMC so I can't comment. I did install a set from classic parts of America and they are fine. I did have to trim them a little, but i would expect that from any vendor. Can't comment on longevity as they are only 5-6 mos old. I don't believe that these seals are meant to do as much as some expect out of them. The weep holes in the bottom of the door are there for a reason......

https://www.classicparts.com/1967-72...ctinfo/03-571/
I just rec. these same ones from Classic Parts....They are Precision brand & look good....not installed yet.
72bowtiestepper is offline   Reply With Quote
Old 02-08-2021, 02:26 PM   #6
Thealien
Senior Member
 
Thealien's Avatar
 
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,125
Re: Yet another window seal, fuzzy, belltline, etc. thread

After hearing a couple of people on this forum say the Repop brand was very nice. I Purchased a set they look nice but I have not installed them yet.

https://www.jegs.com/i/LAT+Racing+Oi...ries%20-%20LST
Thealien is offline   Reply With Quote
Old 02-08-2021, 04:30 PM   #7
Gigem
Registered User
 
Gigem's Avatar
 
Join Date: Feb 2012
Location: Lakeway, TX
Posts: 335
Re: Yet another window seal, fuzzy, belltline, etc. thread

Someone install these darn things and give a report!
__________________
1972 GMC Sierra Grande (current truck)
1980 Chevy Stepside (gone)
1987 Chevy Blazer (gone)
1972 Chevelle SS Convertible (gone)
1973 Chevy Corvette (gone)
1967 Chevy Camaro (STOLEN!)
Gigem is offline   Reply With Quote
Old 02-08-2021, 04:43 PM   #8
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,443
Re: Yet another window seal, fuzzy, belltline, etc. thread

Regardless of the brand you choose, I would suggest checking the strap that spot welds the door halves together near the vent window(72 will have a screw as well as the strap) if the strap or welds are cracked, you’ll have a hard time getting the outer lower window “squeegee” rubber to sit correctly against the window. I used precision for the windows and doors and haven’t had any problems associated with any of the rubbers.
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s
57taskforce is offline   Reply With Quote
Old 02-08-2021, 04:46 PM   #9
1971Stepside
Almost Satisfied
 
1971Stepside's Avatar
 
Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
Re: Yet another window seal, fuzzy, belltline, etc. thread

I tried the LMC ones and my windows would not roll up all the way. I purchased the glue on outers. They fit great, stick and my window go all the way up. On the inner I simply applied the fuzzy side of Velcro. Wish I had bought the glue on ones to start with. They are a precision part as well.
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021.

"I can't complain, but sometimes I still do. Life's been good to me so far."
1971Stepside is offline   Reply With Quote
Old 02-08-2021, 04:47 PM   #10
1971Stepside
Almost Satisfied
 
1971Stepside's Avatar
 
Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
Re: Yet another window seal, fuzzy, belltline, etc. thread

Here is a pic of them installed.
Attached Images
 
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021.

"I can't complain, but sometimes I still do. Life's been good to me so far."
1971Stepside is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:07 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com