GA WTB Clutch Linkage & Door Latch Parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**cwcarpenter98** · 03-28-2021, 09:18 PM

Was underneath my truck yesterday and noticed that the clutch linkage rod is about half way worn through. I did see the replacement that's available online, but I'm not sure of the quality of it.

I need the rod that goes from the clutch pedal to the z-bar. I think I probably also need a z-bar as the hole has gone egg shaped from wear. (Edit to add: Now that I look again at the pictures, maybe I don't need the z-bar.)
Was there some sort of bushing from the factory that was supposed to be there?

On the door latch stuff, I need the latch and striker for the passenger side. Both are heavily worn and I can't get the passenger door to close good at all.

I could also use a passenger window regulator in good condition, but that would be kinda costly to ship, so I might just try rebuilding the one I have.

Any input is welcome here

**DPowers** · 03-28-2021, 11:12 PM

You going to be at Commerce this weekend?

**chtr65** · 03-28-2021, 11:33 PM

I can probably help you out with the door latch items. If I have them, you pay shipping and there yours. Thanks for being a moderator.

**cwcarpenter98** · 03-29-2021, 06:07 AM

Quote:

Originally Posted by DPowers

You going to be at Commerce this weekend?

I haven't made any plans for this weekend, so that's a possibility

Quote:

Originally Posted by chtr65

I can probably help you out with the door latch items. If I have them, you pay shipping and there yours. Thanks for being a moderator.

I forgot to specify that I need them for my 63. If that's what you have, it'll probably fit in a USPS flat rate box. Thank you!

**chtr65** · 03-29-2021, 10:54 AM

Mine would be for 64 thru 66. Sorry for not picking up on that.

**cwcarpenter98** · 03-29-2021, 12:59 PM

Quote:

Originally Posted by chtr65

Mine would be for 64 thru 66. Sorry for not picking up on that.

No worries, thank you for your generosity!

I should have specified 63 in the original post and I plum forgot

**DPowers** · 03-29-2021, 02:26 PM

Quote:

Originally Posted by cwcarpenter98

I haven't made any plans for this weekend, so that's a possibility

I forgot to specify that I need them for my 63. If that's what you have, it'll probably fit in a USPS flat rate box. Thank you!

Let me know. Probably have all you looking for. Will have to check on clutch piece. Got a length?

**cwcarpenter98** · 03-29-2021, 08:16 PM

Quote:

Originally Posted by DPowers

Let me know. Probably have all you looking for. Will have to check on clutch piece. Got a length?

It looks like it's approximately 20". It's a slight challenge to measure unless I take it out of the truck, but I can pull it out for a better measurement if needed. Looks like where it attaches at the pedal is worn out as well, so I probably need to get that piece too

1960chevypanel · 03-29-2021, 06:30 PM

I can help with the door stuff if the other guys don't have it

**cwcarpenter98** · 03-29-2021, 08:20 PM

Quote:

Originally Posted by 1960chevypanel

I can help with the door stuff if the other guys don't have it

Thank you. I think I'll end up going to Commerce this weekend, but I'll let you know if I don't find what I need

**Riverstory** · 03-31-2021, 01:21 AM

I have a clutch linkage rod with minor wear if you want it - cost me nothing. But . . .

I cut my existing rod, threaded the rod and then added Heim joints. I eliminated the friction of metal on metal.

And on the clutch part that egg shaped, I welded it and re-drilled the hole.

**cwcarpenter98** · 03-31-2021, 12:22 PM

Quote:

Originally Posted by Riverstory

I have a clutch linkage rod with minor wear if you want it - cost me nothing. But . . .

I cut my existing rod, threaded the rod and then added Heim joints. I eliminated the friction of metal on metal.

And on the clutch part that egg shaped, I welded it and re-drilled the hole.

Thank you for your generosity. Dwayne has one as well that I don't have to have shipped, so I'll be getting it this weekend.

I did see that mod, but unfortunately for me, I don't have a tap and die set yet and my welder is back home in Woodstock while I'm in Milledgeville till the end of April. Before I install the new to me parts, I'm going to look into using either a nylon or bronze bushing to take up any slack keep it from wearing through again

**cwcarpenter98** · 03-31-2021, 12:18 PM

Thanks for the offer of parts, guys. Dwayne has all the parts that I needed this go around, so I'll be one stop shopping at Commerce this weekend

03-28-2021, 09:18 PM	#1
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,508	WTB Clutch Linkage & Door Latch Parts Was underneath my truck yesterday and noticed that the clutch linkage rod is about half way worn through. I did see the replacement that's available online, but I'm not sure of the quality of it. I need the rod that goes from the clutch pedal to the z-bar. I think I probably also need a z-bar as the hole has gone egg shaped from wear. (Edit to add: Now that I look again at the pictures, maybe I don't need the z-bar.) Was there some sort of bushing from the factory that was supposed to be there? On the door latch stuff, I need the latch and striker for the passenger side. Both are heavily worn and I can't get the passenger door to close good at all. I could also use a passenger window regulator in good condition, but that would be kinda costly to ship, so I might just try rebuilding the one I have. Any input is welcome here Attached Images __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson Last edited by cwcarpenter98; 03-28-2021 at 09:23 PM.

03-28-2021, 11:12 PM	#2
DPowers One foot in front of the other Join Date: Aug 2008 Location: Parrottsville, TN Posts: 5,459	Re: WTB Clutch Linkage & Door Latch Parts You going to be at Commerce this weekend? __________________ DP's 66 Build http://67-72chevytrucks.com/vboard/s...d.php?t=361556

03-28-2021, 11:33 PM	#3
chtr65 Registered User Join Date: Mar 2013 Location: Lewisberry, Pa. Posts: 544	Re: WTB Clutch Linkage & Door Latch Parts I can probably help you out with the door latch items. If I have them, you pay shipping and there yours. Thanks for being a moderator.

03-29-2021, 10:54 AM	#5
chtr65 Registered User Join Date: Mar 2013 Location: Lewisberry, Pa. Posts: 544	Re: WTB Clutch Linkage & Door Latch Parts Mine would be for 64 thru 66. Sorry for not picking up on that.

03-29-2021, 06:30 PM	#9
1960chevypanel Registered User Join Date: Aug 2010 Location: Southern CA Posts: 1,629	Re: WTB Clutch Linkage & Door Latch Parts I can help with the door stuff if the other guys don't have it

03-31-2021, 01:21 AM	#11
Riverstory Registered User Join Date: Aug 2020 Location: Lake Havasu City AZ Posts: 142	Re: WTB Clutch Linkage & Door Latch Parts I have a clutch linkage rod with minor wear if you want it - cost me nothing. But . . . I cut my existing rod, threaded the rod and then added Heim joints. I eliminated the friction of metal on metal. And on the clutch part that egg shaped, I welded it and re-drilled the hole.

03-31-2021, 12:18 PM	#13
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,508	Re: WTB Clutch Linkage & Door Latch Parts Thanks for the offer of parts, guys. Dwayne has all the parts that I needed this go around, so I'll be one stop shopping at Commerce this weekend __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.