wtb driveshaft - The 1947 - Present Chevrolet & GMC Truck Message Board Network

redneck · 12-29-2003, 11:03 PM

I'm looking for a driveshaft to bolt into my 67 with a turbo 400 trans. It needs to be a minimum of 70 1/4" long and a max of 70 3/4 " long. I believe a drive shaft out of a big block longbed 2 wheel drive truck has the correct length that I'm looking for.

Shane's Parts · 12-30-2003, 10:42 AM

bump

Slammed67 · 12-30-2003, 11:24 AM

2-piece? I have a 2-piece driveshaft, but i'll have to measure it to see if it's the right length. I'll try to check on it this evening.

Jason

**Tim Christian** · 12-30-2003, 11:31 AM

I have a one peice out of a 67 LWB GMC it is 68-1/2in long measuring from u-joint to u-joint this is not counting the yoke

redneck · 12-31-2003, 03:11 PM

Im going to cut 3'' out of my old one thanks.

redneck · 12-31-2003, 03:12 PM

bumb

Class of 69 · 01-01-2004, 02:10 AM

I have a factory original 2 piece out of a 69 2wd long bed, big block truck with the 400 yoke on it. Has the heavy duty carrier bearing. All in bolt in condition. $ 65.00 plus shipping. I might be able to get it to Teeitups for a small fee, if you can pick it up there. PM me if you're interested. Thanks

Shane's Parts · 01-02-2004, 10:33 AM

Thanks to everyone who responded... However redneck has decided to go ahead and have his old driveshaft cut to fit.. thanks again to everyone for their input.....

12-29-2003, 11:03 PM	#1
redneck Registered User Join Date: Dec 2003 Location: liberty mo. Posts: 6	wtb driveshaft I'm looking for a driveshaft to bolt into my 67 with a turbo 400 trans. It needs to be a minimum of 70 1/4" long and a max of 70 3/4 " long. I believe a drive shaft out of a big block longbed 2 wheel drive truck has the correct length that I'm looking for.

12-30-2003, 11:24 AM	#3
Slammed67 Progress = 0% Join Date: Nov 2001 Location: Kansas City, MO Posts: 2,108	2-piece? I have a 2-piece driveshaft, but i'll have to measure it to see if it's the right length. I'll try to check on it this evening. Jason __________________ Jason - '67 GMC swb \| '57 Bel-Air 4dr hardtop \| '56 210 4dr Wagon \| 2000 GMC Sierra

01-01-2004, 02:10 AM	#7
Class of 69 Registered User Join Date: Mar 2003 Location: Stillwater MN Posts: 1,166	I have a factory original 2 piece out of a 69 2wd long bed, big block truck with the 400 yoke on it. Has the heavy duty carrier bearing. All in bolt in condition. $ 65.00 plus shipping. I might be able to get it to Teeitups for a small fee, if you can pick it up there. PM me if you're interested. Thanks __________________ 69 GMC K10 ..some restoration required....still..

12-30-2003, 10:42 AM	#2
Shane's Parts Registered User Join Date: Jan 2003 Location: Kansas City, Mo Posts: 267	bump

12-30-2003, 11:31 AM	#4
Tim Christian Senior Member Join Date: Dec 1999 Location: TN/VA Posts: 6,388	I have a one peice out of a 67 LWB GMC it is 68-1/2in long measuring from u-joint to u-joint this is not counting the yoke

12-31-2003, 03:11 PM	#5
redneck Registered User Join Date: Dec 2003 Location: liberty mo. Posts: 6	Im going to cut 3'' out of my old one thanks.

12-31-2003, 03:12 PM	#6
redneck Registered User Join Date: Dec 2003 Location: liberty mo. Posts: 6	bumb

01-02-2004, 10:33 AM	#8
Shane's Parts Registered User Join Date: Jan 2003 Location: Kansas City, Mo Posts: 267	Thanks to everyone who responded... However redneck has decided to go ahead and have his old driveshaft cut to fit.. thanks again to everyone for their input.....



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.