TA bushings - The 1947 - Present Chevrolet & GMC Truck Message Board Network

kev2809 · 03-20-2022, 08:48 PM

installed brand new bushings and trying to get my TA's back in with the anti squat brackets and they look to be about 1/4" too wide. anyone have this problem..and can they be shaved down to fit? lined them up with the stock brackets and same problem.

SCOTI · 03-20-2022, 10:05 PM

I'll take some pics of the last set-up I did w/Poly bushings. I still have the arms for mock-up use so they might provide some insight. It will probably be sometime after the lunch hours tomorrow to get some pics up & the discussin started.

kev2809 · 03-20-2022, 10:19 PM

ok no problem. supposed to be getting some rain the next few days so I probably can't get to the truck u til Wednesday. you can see in the 1st pic the "lip" I'm thinking I can trim down flush? the last pic shows how much more it sticks out than the other side

kev2809 · 03-22-2022, 10:44 PM

had some time to get it at it today and ended up trimming that side down...it was the only way and it's still a tight fit. I trimmed the outside rubber until it was flush with the center metal bushing

kev2809 · 03-22-2022, 10:48 PM

but after getting all the rear suspension bolted back with new bags...it seems the axle shifted backwards (angled up). the only thing I replaced differently than what I had was anti squat brackets..but I set them at the bottom hole which is supposed to be stock degree.

so frustrating...truck looks great slammed and although haven't tested my pinion angles, the way it sits now seems like the old driveshaft won't even fit.

SCOTI · 03-24-2022, 09:00 AM

Took me longer than expected because these were buried under sheet metal brought into the shop when I moved out of a storage unit a couple years ago.

These are Energy Suspension poly bushings despite their appearance. Both sides appear relatively flush on my set-up. I have a T/A x-member on a cart so I checked the fit. It's possible the mounts were opened slightly @ some point but I don't remember a specifically doing it.

Note the condition (appearance) of the bushings. These were put into service probably around late '98 or early '99 & the truck was off the road by '05. They feel like freakin' concrete. I had to run these because I had things apart & couldn't find rubber replacements @ the time. This is why I only like the OE style rubber or a spherical type of joint @ this position.

kev2809 · 03-24-2022, 11:53 AM

yup thats basically what mine look like now. I need to see what brand they are

03-20-2022, 08:48 PM	#1
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,178	TA bushings installed brand new bushings and trying to get my TA's back in with the anti squat brackets and they look to be about 1/4" too wide. anyone have this problem..and can they be shaved down to fit? lined them up with the stock brackets and same problem. Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

03-20-2022, 10:05 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	Re: TA bushings I'll take some pics of the last set-up I did w/Poly bushings. I still have the arms for mock-up use so they might provide some insight. It will probably be sometime after the lunch hours tomorrow to get some pics up & the discussin started. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

03-20-2022, 10:19 PM	#3
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,178	Re: TA bushings ok no problem. supposed to be getting some rain the next few days so I probably can't get to the truck u til Wednesday. you can see in the 1st pic the "lip" I'm thinking I can trim down flush? the last pic shows how much more it sticks out than the other side __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

03-22-2022, 10:44 PM	#4
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,178	Re: TA bushings had some time to get it at it today and ended up trimming that side down...it was the only way and it's still a tight fit. I trimmed the outside rubber until it was flush with the center metal bushing Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

03-22-2022, 10:48 PM	#5
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,178	Re: TA bushings but after getting all the rear suspension bolted back with new bags...it seems the axle shifted backwards (angled up). the only thing I replaced differently than what I had was anti squat brackets..but I set them at the bottom hole which is supposed to be stock degree. so frustrating...truck looks great slammed and although haven't tested my pinion angles, the way it sits now seems like the old driveshaft won't even fit. __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

03-24-2022, 09:00 AM	#6
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	Re: TA bushings Took me longer than expected because these were buried under sheet metal brought into the shop when I moved out of a storage unit a couple years ago. These are Energy Suspension poly bushings despite their appearance. Both sides appear relatively flush on my set-up. I have a T/A x-member on a cart so I checked the fit. It's possible the mounts were opened slightly @ some point but I don't remember a specifically doing it. Note the condition (appearance) of the bushings. These were put into service probably around late '98 or early '99 & the truck was off the road by '05. They feel like freakin' concrete. I had to run these because I had things apart & couldn't find rubber replacements @ the time. This is why I only like the OE style rubber or a spherical type of joint @ this position. Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

03-24-2022, 11:53 AM	#7
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,178	Re: TA bushings yup thats basically what mine look like now. I need to see what brand they are __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.