|
01-22-2005, 11:56 AM
|
#1 |
|
Franko72
Join Date: May 2004
Location: Cincinnati,Ohio
Posts: 471
|
side trim removal
I am going to be removing the trim to start paint and body work. How do you remove the upper and lower trim on a cheyenne without messing up the trim pieces?
__________________
 1972 C20 cheyenne Super 402 BB/400 turbo LWB A/C Tilt, Cruise Control, Saddle tanks, Tach My Home Page Better to burn out than it is to rust |
|
|
|
01-22-2005, 08:26 PM
|
#2 |
|
Franko72
Join Date: May 2004
Location: Cincinnati,Ohio
Posts: 471
|
I know it seems easy to some that have done this. I am looking for tips ,Do's & Dont's. Anyone out there?Any trim removal tools needed?
__________________
1972 C20 cheyenne Super 402 BB/400 turbo LWB A/C Tilt, Cruise Control, Saddle tanks, Tach My Home Page Better to burn out than it is to rust |
|
|
|
|
01-22-2005, 09:07 PM
|
#3 |
|
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
Well, I know that almost all of it is bolted on, just remove all the nuts that hold it on and be careful when taking it off. I can take all of the lower bed trim and fender trim off my truck just by crawling under it and using a 3/8" endwrench. It's kinda hard to get to the fender trim though. I haven't tried taking the upper trim off yet so I'm not sure about that stuff.
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck Last edited by Robert1970C20rstbukt; 01-22-2005 at 09:10 PM. |
|
|
|
|
01-23-2005, 01:13 AM
|
#4 |
|
Registered User
Join Date: Mar 2004
Location: Lexington, KY
Posts: 865
|
Some of the clips are glued on to the truck too. A flexible putty knife will work well on those.
|
|
|
|
|
01-23-2005, 10:47 AM
|
#5 |
|
Registered User
Join Date: Jan 2002
Location: Sahuarita, AZ USA
Posts: 2,033
|
Don't know on our trucks specifically, cuz mine doesn't have any, but usually, they are screwed in front and rear, and I've just slid them off, exposing the remaining retainers.
__________________
Bill - Tucson, AZ 47 Chevrolet 2 dr sedan 56 Chevrolet 210 2 dr sedan 66 Chevrolet Malibu 2 dr 4 speed 71 Chevrolet C30 Longhorn 86 Chevrolet Monte Carlo SS (Sold) 01 Chevrolet Tahoe IM - BUSTERWIVE@aol.com |
|
|
|
|
01-23-2005, 12:33 PM
|
#6 |
|
Senior Member
 
Join Date: Jul 2001
Location: Hyattsville, Maryland
Posts: 3,685
|
Most of the clips on the upper trim are push in type.I take a small flat screwdriver and stick it between the molding and the body and just push the tabs together and it will come out.The end clips have nuts on them.
__________________
72 Cheyenne Super (Purchased new by my parents in August of 71) Black and White |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
