Wheel Base measurement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

3quartertime · 02-14-2005, 12:31 PM

Hello all, great site first post!!!

I'm lining up going to pick up a Chevy 71 C20 4x4. I need to know wheel base measurements to find a suitable trailer. Does anyone have a link or address for the factory specs. The current owner has bigger tires on the front and says it is 86 inches. Sounds pretty wide.

Thanks!!!

JimKshortstep4x4 · 02-14-2005, 09:06 PM

I don't think that he is that far off. The 1/2 ton rear end outside to outside of the tires is approximatel 76" and I believe the front axle is wider. If I had a K-20 I would get you a measurement but I don't have one.

Jim

Longhorn Man · 02-14-2005, 09:11 PM

The actual wheel base is 127 inches.

BobS · 02-14-2005, 09:29 PM

My trailer is 84" wide on the deck. I hauled a K20 Suburban frame on it that just barely fit, there wasn't more than an inch extra between both sides. It had 33X12.50s on it, not sure what the offset was. Be sure you bring enough trailer, they're wide!

Bob

**JIMs70GMC** · 02-14-2005, 10:01 PM

I had a heck of a time getting my 71 on a dolly, even with narrow tires. 86 does not sound unreasonable.

3quartertime · 02-14-2005, 10:12 PM

Thanks guys.

I'm thinking I may have to back it on the trailer to get it past the wheel wells. Buddy says he's pretty sure it's 82 between the wells. Going to pick up the trailer in the morning and see what the actual is.

dwaite72lnghrn · 02-14-2005, 10:27 PM

I hauled a 71gmc 3/4 with 33-12.5x16.5 tires on my 7'x16' big tex trailers. I had about 1 inch space between the fenders.

02-14-2005, 12:31 PM	#1
3quartertime My Mistress the Sea Join Date: Feb 2005 Location: Bradenton, FL. Posts: 412	Wheel Base measurement Hello all, great site first post!!! I'm lining up going to pick up a Chevy 71 C20 4x4. I need to know wheel base measurements to find a suitable trailer. Does anyone have a link or address for the factory specs. The current owner has bigger tires on the front and says it is 86 inches. Sounds pretty wide. Thanks!!!

02-14-2005, 09:29 PM	#4
BobS Senior Member Join Date: May 2001 Location: West Central Minnesota Posts: 568	My trailer is 84" wide on the deck. I hauled a K20 Suburban frame on it that just barely fit, there wasn't more than an inch extra between both sides. It had 33X12.50s on it, not sure what the offset was. Be sure you bring enough trailer, they're wide! Bob __________________ V-6....only GMC Trucks have it! 62 GMC W5000 NAPCO-V6 65 GMC 2500 NAPCO Panel-V6 66 GMC 1000-V6 66 GMC 1500-V6 67 GMC K1500-SBC (originally a KM-V6) 68 GMC C1500-V6 68 GMC C1500-V6 68 GMC Suburban C2500 70 Chevy K20-SBC 71 Chevy C30 Longhorn-SBC 72 GMC Suburban C1500-BBC 72 Chevy C10-SBC 72 GMC C5500-ToroFlow Diesel

02-14-2005, 10:01 PM	#5
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	I had a heck of a time getting my 71 on a dolly, even with narrow tires. 86 does not sound unreasonable. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

02-14-2005, 10:27 PM	#7
dwaite72lnghrn Registered User Join Date: Jun 2002 Location: central pa Posts: 1,525	I hauled a 71gmc 3/4 with 33-12.5x16.5 tires on my 7'x16' big tex trailers. I had about 1 inch space between the fenders. __________________ 72 longhorn c30 502BB/th400/fact air/4.11rear/ custom camper 72 bug(the better half's) under reconstruction 2009 HHR aqua blue 71 GMC k20 350/sm465 2009 Chevy hd3500 6.6 Victory Red crew cab dually Dave & Jeanne

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-14-2005, 09:06 PM	#2
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	I don't think that he is that far off. The 1/2 ton rear end outside to outside of the tires is approximatel 76" and I believe the front axle is wider. If I had a K-20 I would get you a measurement but I don't have one. Jim

02-14-2005, 09:11 PM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	The actual wheel base is 127 inches.

02-14-2005, 10:12 PM	#6
3quartertime My Mistress the Sea Join Date: Feb 2005 Location: Bradenton, FL. Posts: 412	Thanks guys. I'm thinking I may have to back it on the trailer to get it past the wheel wells. Buddy says he's pretty sure it's 82 between the wells. Going to pick up the trailer in the morning and see what the actual is.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.