van tilt column ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dmec · 03-08-2005, 11:33 AM

is it really necessary to relocate neutral safety switch when installing a van column in these trucks?

Tx Firefighter · 03-08-2005, 01:09 PM

Yes it is. Otherwise, the column won't bolt in. It interferes.

Livrat · 03-08-2005, 01:26 PM

Not on all van tilts.. the early ones.. 70 - 73 have the neutral safety switch in the correct location and even have the correct levers.. the only change necessary on them is the shaft length...

**uncle** · 03-08-2005, 06:15 PM

You can remove it, but your truck will start in any gear.

dmec · 03-08-2005, 07:08 PM

thanks for the info. i have 6 columns i plan on rebuilding for sale and didnt know if relocating switch was neccessary. the collars that have loose pins are going to be shaved and turned into floor shift models. i just did a floor shift model for my truck. i shortened the mast 2 inches to get the steering wheel out of my face. much better. i can even see my bottom gauges now.

dmec · 03-08-2005, 07:27 PM

my shortened floor shift tilt.

Brainchild · 03-08-2005, 07:35 PM

Yeah they are much more comfy shoved down in there like that.I left mine up about 2 inches farther than that,but it's much better than a stocker.

I don't have a place for my tach now until I work on the dash

Big Block · 03-08-2005, 07:44 PM

I saw your tach is 7 grand, What is it out of? Is that a early camero tach? I saw one at a venders display at Charlotte NC auto fair. Thanks B.B.

dmec · 03-08-2005, 08:15 PM

yes it is a camaro tach. here is 1 i put in another dash. i also used 80,s truck gauges.

Big Block · 03-08-2005, 08:28 PM

Does it work with the stock printed curcit board? Do you have to make any mods. to make it fit? Thanks B.B.

dmec · 03-08-2005, 08:43 PM

yes it works with the stock printed circuit. there is a trick to it and if i told you i would have to kill you. LOL. just kidding. tried to load picture of back but file is too large. send e mail and i could show pic.

shifty · 03-08-2005, 08:51 PM

If you're using Windows XP, find the actual file on your computer, right-click the file and choose "Edit".

This should open it in MS Paint program.

From the 'Image" menu, choose Stretch/Skew. Change the numbers to be 50%horizontal and 50% vertical and click OK.

This will shrink the dimensions by half. From the 'File' menu, choose "Save as" and save the file as a JPEG with a different name.

The board should let you upload it without a problem.

If it's too small to see the details, you can try doing a 75% shrink.

03-08-2005, 11:33 AM	#1
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	van tilt column ? is it really necessary to relocate neutral safety switch when installing a van column in these trucks?

03-08-2005, 01:09 PM	#2
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Yes it is. Otherwise, the column won't bolt in. It interferes. __________________ I'm on the Instagram- @Gearhead_Kevin

03-08-2005, 06:15 PM	#4
uncle Senior Member Join Date: Aug 2003 Location: Conyers,Ga. Posts: 7,288	Switch You can remove it, but your truck will start in any gear.

03-08-2005, 07:27 PM	#6
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	my shortened floor shift tilt. Attached Images

03-08-2005, 07:35 PM	#7
Brainchild Still drivin' a Rat Rod Join Date: Sep 2004 Location: Monett Missouri Posts: 4,925	Yeah they are much more comfy shoved down in there like that.I left mine up about 2 inches farther than that,but it's much better than a stocker. I don't have a place for my tach now until I work on the dash __________________ Rusty Member #13872 Instead of saying.....you are a discomfort in the back of my front.....one should be able to say...... you are a pain in the a$# 71 GMC LWB 49 Chevy 85 Chevy G20 Check out my website

03-08-2005, 01:26 PM	#3
Livrat Member #1049 Join Date: Jun 2000 Location: Troy Montana Posts: 3,940	Not on all van tilts.. the early ones.. 70 - 73 have the neutral safety switch in the correct location and even have the correct levers.. the only change necessary on them is the shaft length...

03-08-2005, 07:08 PM	#5
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	thanks for the info. i have 6 columns i plan on rebuilding for sale and didnt know if relocating switch was neccessary. the collars that have loose pins are going to be shaved and turned into floor shift models. i just did a floor shift model for my truck. i shortened the mast 2 inches to get the steering wheel out of my face. much better. i can even see my bottom gauges now.

03-08-2005, 07:44 PM	#8
Big Block Big Block Join Date: Mar 2005 Location: Durham, N.C. Posts: 1,649	I saw your tach is 7 grand, What is it out of? Is that a early camero tach? I saw one at a venders display at Charlotte NC auto fair. Thanks B.B.

03-08-2005, 08:15 PM	#9
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	yes it is a camaro tach. here is 1 i put in another dash. i also used 80,s truck gauges. Attached Images

03-08-2005, 08:28 PM	#10
Big Block Big Block Join Date: Mar 2005 Location: Durham, N.C. Posts: 1,649	Does it work with the stock printed curcit board? Do you have to make any mods. to make it fit? Thanks B.B.

03-08-2005, 08:43 PM	#11
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	yes it works with the stock printed circuit. there is a trick to it and if i told you i would have to kill you. LOL. just kidding. tried to load picture of back but file is too large. send e mail and i could show pic.

03-08-2005, 08:51 PM	#12
shifty Questionable Join Date: Mar 2005 Location: Atlanta Posts: 13,373	If you're using Windows XP, find the actual file on your computer, right-click the file and choose "Edit". This should open it in MS Paint program. From the 'Image" menu, choose Stretch/Skew. Change the numbers to be 50%horizontal and 50% vertical and click OK. This will shrink the dimensions by half. From the 'File' menu, choose "Save as" and save the file as a JPEG with a different name. The board should let you upload it without a problem. If it's too small to see the details, you can try doing a 75% shrink. __________________ If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.