need pic of v8 4x4 motor mount stands - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**tnblazerk5** · 04-24-2005, 10:13 AM

i just got the 4x4 v8 crossmemeber now i need to know what the motor mount stands look like so i can hunt those too and how they hook to the crossmemeber ? or is the 2 wheel drive ones the same ?

this is for 67-72 truck

**tnblazerk5** · 04-25-2005, 04:09 AM

am i missing sumthing here ?

jlhusa1 · 04-25-2005, 08:14 AM

What exactly are you trying to do? What trans/tranfer case are you using?

**tnblazerk5** · 04-25-2005, 10:53 AM

Quote:

Originally Posted by jlhusa1

What exactly are you trying to do? What trans/tranfer case are you using?

i am making a 2 wheel drive into a 4 wheel drive and i just received a 4x4 v8 motor crossmemeber how does the motor hook to the crossmemeber? i need a pic of the motor mounts on a v8 4x4 truck please and if it makes a differance its going to be a 350/465/205 in a 1 ton truck

ryanroo · 04-25-2005, 11:12 AM

you can use the 2wd rubber pads for your 4wd conversion i think(never had a 2wd), they just bolt to the engine like normal and then a short like 1 inch long 7/16" bolt with a big washer goes through the holes in the x-member and into the rubber pad that bolts to the engine. i think they are all the same. sorry no pictures but i hope this helps
Ryan

**tnblazerk5** · 04-25-2005, 02:10 PM

Quote:

Originally Posted by ryanroo

you can use the 2wd rubber pads for your 4wd conversion i think(never had a 2wd), they just bolt to the engine like normal and then a short like 1 inch long 7/16" bolt with a big washer goes through the holes in the x-member and into the rubber pad that bolts to the engine. i think they are all the same. sorry no pictures but i hope this helps
Ryan

yea that helps alot thanks !!!!!!!!!!! it means i dont got to buy anything else to put the motor in lol

Russell · 04-25-2005, 02:57 PM

Actually, the brackets that bolt to the engine are significantly different between a 4x4 and a 2wd truck. However, the engine mount cups are the same, and you should have the towers.

04-24-2005, 10:13 AM	#1
tnblazerk5 User #12137 Join Date: Apr 2004 Location: kingsport,upper east tenn Posts: 11,598	need pic of v8 4x4 motor mount stands i just got the 4x4 v8 crossmemeber now i need to know what the motor mount stands look like so i can hunt those too and how they hook to the crossmemeber ? or is the 2 wheel drive ones the same ? this is for 67-72 truck Last edited by tnblazerk5; 04-24-2005 at 10:14 AM.

04-25-2005, 11:12 AM	#5
ryanroo Senior Member Join Date: Apr 2004 Location: sw colorado Posts: 2,720	you can use the 2wd rubber pads for your 4wd conversion i think(never had a 2wd), they just bolt to the engine like normal and then a short like 1 inch long 7/16" bolt with a big washer goes through the holes in the x-member and into the rubber pad that bolts to the engine. i think they are all the same. sorry no pictures but i hope this helps Ryan __________________ 72 K20 12v build 72 K20 "parts truck" A place for your diesel swap questions

04-25-2005, 02:57 PM	#7
Russell Professional Grade Join Date: May 2003 Location: Fort McMurray, Alberta Posts: 7,915	Actually, the brackets that bolt to the engine are significantly different between a 4x4 and a 2wd truck. However, the engine mount cups are the same, and you should have the towers. __________________ 1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-25-2005, 04:09 AM	#2
tnblazerk5 User #12137 Join Date: Apr 2004 Location: kingsport,upper east tenn Posts: 11,598	am i missing sumthing here ?

04-25-2005, 08:14 AM	#3
jlhusa1 Registered User Join Date: Mar 2005 Posts: 15	What exactly are you trying to do? What trans/tranfer case are you using?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.