Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
04-25-2005, 10:31 PM | #1 |
Registered User
Join Date: Mar 2005
Posts: 4
|
Good price for OEM rear 1/4 panels?
Not sure if this is a good deal so would appreciate some suggestions from the board.
Someone local to me is selling "left and right OEM partial rear quarter panels" for $600.-. They are supposed to be in mint condition. I checked out Goodmark and Harmons without finding an equivalent piece either OEM or aftermarket. My '77 has _alot_ of rust in the rear quarter so I this sounds interesting. My question is whether this is a good deal or if someone is trying to fleece me. Suggestions/comments appreciated! -Alex |
05-03-2005, 10:19 AM | #2 |
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
GM only makes complete panels as assembled at plant.Check cheyennetruckparts.com for a price on non-OEM.It sounds good for OEM.They could have been cut-down.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
05-03-2005, 11:41 AM | #3 |
www.73-87chevytrucks.com
Join Date: Dec 1999
Location: Birmingham, AL
Posts: 6,935
|
Does it look like any of these:
http://www.73-87chevytrucks.com/merc..._Code=7387Beds http://www.73-87chevytrucks.com/merc..._Code=7387Beds
__________________
Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com |
05-04-2005, 08:16 AM | #4 | |
Registered User
Join Date: Mar 2005
Posts: 4
|
Quote:
-Alex |
|
05-04-2005, 08:21 AM | #5 | |
Registered User
Join Date: Mar 2005
Posts: 4
|
Quote:
TIA, Alex |
|
05-04-2005, 04:35 PM | #6 |
www.73-87chevytrucks.com
Join Date: Dec 1999
Location: Birmingham, AL
Posts: 6,935
|
http://www.cheyennepickup.com/
I don't know anyone that supplies those. I had to stop since almost everyone I sold was sent back because it wasn't perfect.
__________________
Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com |
06-20-2005, 10:25 PM | #7 |
Registered User
Join Date: Mar 2005
Posts: 4
|
Welll I ended up buying the pieces as they were local to me here in NH. Got both the left and right sides for my project truck. They aren't perfect nor do they have inner fenders on them but they are _alot_ better then those panels on my Jimmy right now.
Putting them on looks like it will be quite a bit of work - though the result will be worthwhile once on. Anyone have a writeup on how to put them on? Next project - replacing the fuel tank and fuel lines. -Alex |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|