Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
07-05-2005, 05:04 PM | #1 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
Pic Request - Blazer Skid Plate
Hey guys, now that I own one of these things, where does it go, I know this sounds stupid, but a picture is
worth a thousand words, and please give them to me as detailed as possible, if they are to large to post you can send them to luv2xclr8@charter.net, Thanks in advance 4 helping (I included some pic's of it 4 ya )
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T Last edited by LUV2XCLR8; 10-23-2005 at 08:40 AM. |
07-05-2005, 08:07 PM | #2 |
Registered User
Join Date: Dec 2004
Location: Gypsum Kansas 67448
Posts: 1,681
|
i dont have a pic,but i am pretty sure it goes behind the tranny x member,and the extended part of that piece w/ the 4 holes,bolts to the tranny x member,it should fit in there like a glove
__________________
21 2500hd duramax 58 apache HILLJOB GRAPHIX--for all your graphic needs My build thread http://67-72chevytrucks.com/vboard/s...d.php?t=542497 LS ENGINE SWAP INFORMATION THREAD http://67-72chevytrucks.com/vboard/s...d.php?t=377348 4l60 to an NP205 http://67-72chevytrucks.com/vboard/s...43#post3697343 |
07-05-2005, 08:38 PM | #3 | |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
Quote:
crossmember, not that it is a big deal to put holes in it, that is the mainly the reason I asked, so I get the holes put in the right place for the install.
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
07-05-2005, 09:00 PM | #4 |
Member #1049
Join Date: Jun 2000
Location: Troy Montana
Posts: 3,940
|
here is a crappy pic I just took of the passengers side skid plate in my 68 GMC with a t350/205...sorry bout the blurr it just started to rain and I took it in a hurry..
Last edited by Livrat; 07-05-2005 at 09:03 PM. |
07-06-2005, 06:53 AM | #5 |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,537
|
Drivers side.
|
07-06-2005, 07:34 AM | #6 |
Registered User
Join Date: Apr 2005
Posts: 41
|
Ahh so that is what that piece is for, lucky i didnt throw it out last year when i couldnt figure out what the heck it was. Does anyone know if there is anything special about the second crossmember or is it the same as the first or what?
|
07-06-2005, 02:32 PM | #7 |
Registered User
Join Date: Feb 2000
Location: Modesto, CA
Posts: 1,842
|
The second x-member is the same. You are missing the upper frame mounts. The piece you have only bolts to the lower part of the frame. THere are two other pices that bolt to the top of the frame then down to the x-member.
Hope this helps Burt
__________________
1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks |
07-06-2005, 03:45 PM | #8 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
Thanks guys, so if I bolt up the plate to the front crossmember I already
have, I should just be able to line up the second member from that point and create a few holes for it, right? Or is there more to it than that?
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
07-06-2005, 10:58 PM | #9 |
JB-80 "Twice as Good"
Join Date: Jun 2004
Location: Central, MN
Posts: 354
|
"git-r-done"!!!!
__________________
HEY NOW! |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|