tranny cooler lines install? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BUXMAN66 · 08-25-2002, 10:32 PM

anyone tried to put some new lines in their truck w/engine in already?(hoses,etc..) what a bitc@ of a time!!kinda ruins the whole idea of pre-bent lines,eh? and they're s/s to boot!!anyone got any bright idea's?

O'l Buck · 08-26-2002, 02:51 AM

i went the easy route and cut the bad spots out and reconnected the lines with fuel hose....just till i decide to rebuild the engine and then i'm putting in new lines.

JimKshortstep4x4 · 08-26-2002, 07:27 AM

That is the way we install the lines. They will go in from the front. It is a little tricky and some times you have to deflect them a little
to wiggle them into place. There is no way to describe how it is done other than to snake the lines in. I usually put the lower one in first and save the upper for last, (the upper being longer is more difficult).

Jim

BUXMAN66 · 08-27-2002, 01:22 PM

i decided to yank out the new cooler lines that i installed this past wkend. just looks kinda junky in a nice clean engine compartment to have the lines all twisted 'round in the front of your engine for everyone to see! found a cool little set-up w/ jegs it is part #771-1003.goes on the inside of your frame rail,and will install w/high pressure rubber hose. 1.5"x 2"x24"long.the jr.cooler is the same except 17"long.and no, i ain't towing w/this truck!

08-25-2002, 10:32 PM	#1
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	tranny cooler lines install? anyone tried to put some new lines in their truck w/engine in already?(hoses,etc..) what a bitc@ of a time!!kinda ruins the whole idea of pre-bent lines,eh? and they're s/s to boot!!anyone got any bright idea's? __________________ '68 swb 1/2t 350/350th '86 lngbd 3/4 TON parts getter '49 gmc 1/2 t 5 window 350/350th '96 gmc sonoma sle ext-cab. hey it's a 4cyl. 5 spd and good on gas y'know?

08-26-2002, 02:51 AM	#2
O'l Buck Recovering Truck Driver Join Date: Mar 2002 Location: Orleans, NE USA Posts: 1,883	i went the easy route and cut the bad spots out and reconnected the lines with fuel hose....just till i decide to rebuild the engine and then i'm putting in new lines. __________________ 67 K-20 350, SM465, Eaton rear, 4.56 no spin option 00 Dodge 2500 4x4, 24V cummins, 5 speed Chad South Central Nebraska

08-27-2002, 01:22 PM	#4
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	i decided to yank out the new cooler lines that i installed this past wkend. just looks kinda junky in a nice clean engine compartment to have the lines all twisted 'round in the front of your engine for everyone to see! found a cool little set-up w/ jegs it is part #771-1003.goes on the inside of your frame rail,and will install w/high pressure rubber hose. 1.5"x 2"x24"long.the jr.cooler is the same except 17"long.and no, i ain't towing w/this truck! __________________ '68 swb 1/2t 350/350th '86 lngbd 3/4 TON parts getter '49 gmc 1/2 t 5 window 350/350th '96 gmc sonoma sle ext-cab. hey it's a 4cyl. 5 spd and good on gas y'know?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-26-2002, 07:27 AM	#3
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	That is the way we install the lines. They will go in from the front. It is a little tricky and some times you have to deflect them a little to wiggle them into place. There is no way to describe how it is done other than to snake the lines in. I usually put the lower one in first and save the upper for last, (the upper being longer is more difficult). Jim



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.