![]() |
![]() |
#1 |
Senior Member
Join Date: Apr 2005
Location: Joppa, Maryland
Posts: 4,408
|
Oil Pan Removal ?
Can the 350 CI oil pan be removed on our trucks, without lifting the engine up or out completely?
__________________
1997 GMC Sierra Ext 1965 Mustang |
![]() |
![]() |
![]() |
#2 |
67 is sold
Join Date: Apr 2001
Location: Troy, Michigan
Posts: 6,738
|
Re: Oil Pan Removal ?
I was told it has to come up a few inches at least
![]() Just unbolt the two mounts, the trans mount and lift a little |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Feb 2003
Location: Iowa
Posts: 974
|
Re: Oil Pan Removal ?
I think you can if it is a 4 wheel drive but other wise you have to un-bolt motor mounts and trans mounts. Just take the bolts out that go through the frame then put a bottle jack under the balancer then put a 2by4 inbetween the mount and frame and take the inspection cover off. Then you should be able to get the pan out.
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Apr 2005
Location: Joppa, Maryland
Posts: 4,408
|
Re: Oil Pan Removal ?
That's what I was afraid of.....thanks for the info. That's what I'll have to do then........
__________________
1997 GMC Sierra Ext 1965 Mustang |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Sep 2005
Location: San Angelo or Eufaula
Posts: 301
|
Re: Oil Pan Removal ?
Quote:
Don't take the trans mount bolts completely out, just back them out 1/2" or so and it will give you enough play to raise the front up plenty. I'd use a cherry picker to lift if available. Bottle jack and 2x4 prone to give ya problems, don't ask me how I know. Kirk |
|
![]() |
![]() |
![]() |
#6 |
Professional Grade
Join Date: May 2003
Location: Fort McMurray, Alberta
Posts: 7,915
|
Re: Oil Pan Removal ?
Make sure you secure the engine once you've lifted it. You can very easily loose fingers if a bottle jack fails while you've got your fingers up there.
__________________
1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap) |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,234
|
Re: Oil Pan Removal ?
jack it up and take an 2x4 and cut an slit in it for the bolt and place it in between the motor mount and frame it will hold engine up
|
![]() |
![]() |
![]() |
#8 |
Msgt USAF Ret
![]() ![]() Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,714
|
Re: Oil Pan Removal ?
be careful of the distributor cap if it is close to the firewall or you might crack it before you realize it.
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
![]() |
![]() |
![]() |
#9 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: Oil Pan Removal ?
Unbolt the fan shroud too or you will crack it when you jack the engine.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#10 | |
~Rest In Peace~
Join Date: May 2005
Location: CALIFORNIA NOR CAL
Posts: 9,707
|
Re: Oil Pan Removal ?
Quote:
the problem would be bearings get wiped out and pressure on the crankshaft isnt good for it too ![]()
__________________
is it fast ? it has a lighting bolt donut? B___H please, I can remove 90% of your so called "beauty" with a kleenex |
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|