Opinion please... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

IGOR · 07-13-2006, 03:15 PM

So - I'm going to attempt to attempt taking the tub off the frame Sat morning - I'm really jonesing to get my frame powdercoated - and I can get it done for free - I'm thinking I'm going to do it on the side of the house - cause my garage is barely big enough to hold flatulence...

Anyway - I have a nice concrete pad on the side of the house - and I drew this up today - a frame built from 2x6s - the Blazer will either be on top - or have another cross bar underneath - so that the A-frame is supported while I'm jacking the body up. The dimensions shown are purely reference and are subject to change and/or miscalculation. The lifting will be done with an engine hoist - this will merely be used to hold the tub - (not to string a hoist from)

Thoughts - opinions - any better ideas

I'm probably going to spray paint the A-frame chrome - just so it is a little stronger - (and so the neighbor has something nice to look at)

bouncytruck · 07-13-2006, 03:41 PM

I'd attach the whole thing to a piece fof 3/4 ply wood to tie the bottoms of the legs together. It would be flat so you could roll the frame out from under the tub.

makovai · 07-13-2006, 05:02 PM

as i told you before i have a body hoist i used for my vette and a chain hoist with rolers it should pick it up no prob. after i got the body off i used a cherry picker to move it around.

cdowns · 07-13-2006, 05:04 PM

i'd think you should put a small diagonial from the uprights to the cross bar to prevent it from a side to side wobble

IGOR · 07-13-2006, 05:04 PM

I saw that - I just don't know how I'd support that - I'm not worried about lifting the body off the frame (or maybe I am a little bit) - I'm worried about supporting it securely outside -

bouncytruck · 07-13-2006, 06:02 PM

How about some braces out to the side.

IGOR · 07-13-2006, 09:42 PM

Oh look at you and your badself

RunTMCfan · 07-14-2006, 01:28 AM

You would need lateral support somewhere. Whether inside the the legs (cross beam) or outside.

Chevyman63 · 07-14-2006, 06:07 AM

There ya go bouncy, now that looks a lot safer.

makovai · 07-14-2006, 11:30 AM

id use more duct tape.

bouncytruck · 07-14-2006, 11:40 AM

Quote:

Originally Posted by makovai

id use more duct tape.

What about bailing wire?

Tynee · 07-14-2006, 01:10 PM

Quote:

Originally Posted by bouncytruck

What about bailing wire?

Don't forget the J.B. Weld!!

krue · 07-14-2006, 01:30 PM

Quote:

Originally Posted by bouncytruck

What about bailing wire?

Overkill.

xchevyxtc · 07-14-2006, 03:31 PM

I used 4x4's on those prebuilt metal sawhorses which i beefed up with some added shearing and the 4x4's broke. I then switched to 4x6's and it held the blazer's body up while i rolled out the chassis.. i used two 4x6's 10' in length and 4 of those sawhorses. just offering an example of what did and did not work for me. Hope it helps!!

**special-K** · 07-16-2006, 07:49 AM

Milk crates and drywall buckets is all I use.But,then again,I`m down to 1 1/2 arms,1 foot and my head is kinda flat on one side.I think they did a great job,though.Besides,who can see both sides at the same time?I always turn my head a little while talking to people in front of me.Oh!I have a safety tip:Make sure there are people around when you nab the milk crates.I thought the opposite and tryed when no one would see.Well,a guy from the store was goin`on a smoke break and musta heard me from inside.He grabbed his shotgun an put a load in my tail.I think I limp more from that than from the prosthetic.

meathead95 · 07-16-2006, 11:41 AM

pm alexis about it he took his off with a cherry picker

vtblazer · 07-16-2006, 02:08 PM

I've used the post's on saw horse thing brfoe but put in back on with a cherry picker.
I went slow and was very methodic but it still made for an interesting chore.

I had already sectioned off the firewall so it was a fair amount lighter.

07-13-2006, 03:15 PM	#1
IGOR Registered User Join Date: Feb 2003 Location: Damascus, OR Posts: 260	Opinion please... So - I'm going to attempt to attempt taking the tub off the frame Sat morning - I'm really jonesing to get my frame powdercoated - and I can get it done for free - I'm thinking I'm going to do it on the side of the house - cause my garage is barely big enough to hold flatulence... Anyway - I have a nice concrete pad on the side of the house - and I drew this up today - a frame built from 2x6s - the Blazer will either be on top - or have another cross bar underneath - so that the A-frame is supported while I'm jacking the body up. The dimensions shown are purely reference and are subject to change and/or miscalculation. The lifting will be done with an engine hoist - this will merely be used to hold the tub - (not to string a hoist from) Thoughts - opinions - any better ideas I'm probably going to spray paint the A-frame chrome - just so it is a little stronger - (and so the neighbor has something nice to look at) __________________ -Ben 1972 CST K5 - Undergoing frame off, 8.1/4L80E/NP205, 3/4 ton, 8" lift, currently a pile of parts that when assembled resemble a Blazer 1972 K10 - Rust Bucket, TBD 1976 C10 SWB, 350 / T350 My blazer build thread: https://ck5.com/forums/builds/72-k5-...17-update.410/ Last edited by IGOR; 07-13-2006 at 03:17 PM.

07-13-2006, 03:41 PM	#2
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Re: Opinion please... I'd attach the whole thing to a piece fof 3/4 ply wood to tie the bottoms of the legs together. It would be flat so you could roll the frame out from under the tub. __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

07-13-2006, 05:02 PM	#3
makovai Senior Member Join Date: Feb 2006 Location: oregon city Posts: 335	Re: Opinion please... as i told you before i have a body hoist i used for my vette and a chain hoist with rolers it should pick it up no prob. after i got the body off i used a cherry picker to move it around. __________________ If it aint broke..............fix it till it is. www.fast77.com 1972 - 330 hp crate, 11" lift with 39x18 mickeys. 3/4 ton, cross steer, 4 wheel disc brakes 1996 Z71 w/ 35's Last edited by makovai; 07-13-2006 at 05:09 PM.

07-13-2006, 05:04 PM	#4
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Opinion please... i'd think you should put a small diagonial from the uprights to the cross bar to prevent it from a side to side wobble __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

07-13-2006, 05:04 PM	#5
IGOR Registered User Join Date: Feb 2003 Location: Damascus, OR Posts: 260	Re: Opinion please... I saw that - I just don't know how I'd support that - I'm not worried about lifting the body off the frame (or maybe I am a little bit) - I'm worried about supporting it securely outside - __________________ -Ben 1972 CST K5 - Undergoing frame off, 8.1/4L80E/NP205, 3/4 ton, 8" lift, currently a pile of parts that when assembled resemble a Blazer 1972 K10 - Rust Bucket, TBD 1976 C10 SWB, 350 / T350 My blazer build thread: https://ck5.com/forums/builds/72-k5-...17-update.410/

07-13-2006, 06:02 PM	#6
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Re: Opinion please... How about some braces out to the side. Attached Images __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

07-13-2006, 09:42 PM	#7
IGOR Registered User Join Date: Feb 2003 Location: Damascus, OR Posts: 260	Re: Opinion please... Oh look at you and your badself __________________ -Ben 1972 CST K5 - Undergoing frame off, 8.1/4L80E/NP205, 3/4 ton, 8" lift, currently a pile of parts that when assembled resemble a Blazer 1972 K10 - Rust Bucket, TBD 1976 C10 SWB, 350 / T350 My blazer build thread: https://ck5.com/forums/builds/72-k5-...17-update.410/ Last edited by IGOR; 07-13-2006 at 09:42 PM.

07-14-2006, 01:28 AM	#8
RunTMCfan Registered User Join Date: Oct 2005 Location: San Diego, Ca Posts: 251	Re: Opinion please... You would need lateral support somewhere. Whether inside the the legs (cross beam) or outside. __________________ Rob "RunTMCfan"

07-14-2006, 06:07 AM	#9
Chevyman63 Can't wait to retire!! Join Date: Feb 2003 Location: Corunna, MI Posts: 1,575	Re: Opinion please... There ya go bouncy, now that looks a lot safer.

07-14-2006, 11:30 AM	#10
makovai Senior Member Join Date: Feb 2006 Location: oregon city Posts: 335	Re: Opinion please... id use more duct tape. __________________ If it aint broke..............fix it till it is. www.fast77.com 1972 - 330 hp crate, 11" lift with 39x18 mickeys. 3/4 ton, cross steer, 4 wheel disc brakes 1996 Z71 w/ 35's

07-14-2006, 03:31 PM	#14
xchevyxtc Registered User Join Date: Jul 2004 Location: Costa Mesa, California Posts: 17	Re: Opinion please... I used 4x4's on those prebuilt metal sawhorses which i beefed up with some added shearing and the 4x4's broke. I then switched to 4x6's and it held the blazer's body up while i rolled out the chassis.. i used two 4x6's 10' in length and 4 of those sawhorses. just offering an example of what did and did not work for me. Hope it helps!!

07-16-2006, 07:49 AM	#15
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Opinion please... Milk crates and drywall buckets is all I use.But,then again,I`m down to 1 1/2 arms,1 foot and my head is kinda flat on one side.I think they did a great job,though.Besides,who can see both sides at the same time?I always turn my head a little while talking to people in front of me.Oh!I have a safety tip:Make sure there are people around when you nab the milk crates.I thought the opposite and tryed when no one would see.Well,a guy from the store was goin`on a smoke break and musta heard me from inside.He grabbed his shotgun an put a load in my tail.I think I limp more from that than from the prosthetic. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

07-16-2006, 11:41 AM	#16
meathead95 computer illiterate Join Date: Jan 2001 Location: Des Moines, IA Posts: 6,440	Re: Opinion please... pm alexis about it he took his off with a cherry picker __________________ 72 2wd blazer 72 swb 4x4

07-16-2006, 02:08 PM	#17
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,537	Re: Opinion please... I've used the post's on saw horse thing brfoe but put in back on with a cherry picker. I went slow and was very methodic but it still made for an interesting chore. I had already sectioned off the firewall so it was a fair amount lighter. Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.