|
08-29-2006, 12:09 AM
|
#1 |
|
RIP Mr Ron
 
Join Date: Dec 2005
Location: Big Sandy, Tn. 38221
Posts: 8,166
|
Can this be done.
I have an old 1967 C-30 truck that needs everything. It is complete but wore out. I have 3 mid seventies 1 tons with good front ends under them. Can I do like the C-10 guys and swap a late model front cross member with a power steering box under it. Has anyone done it and what kind of trouble did you have. I know it would be a lot easier to just build the later models but I just can't take this old girl apart. Any help is appreciated. Thanks.
__________________
Ron (Mr Round Tuit)  Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket |
|
|
|
08-29-2006, 08:53 AM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Can this be done.
It should be pretty much a bolt in, but you will have to "oblong" a couple bolt holes. The crossmembers are said to be the same , from 10-30 series. Just be sure to use ALL the steering linkage from the later truck. best of luck,
 L
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
08-29-2006, 09:54 AM
|
#3 |
|
Junior Member
Join Date: Feb 2005
Location: Huntingburg IN
Posts: 620
|
Re: Can this be done.
I have not done this swap on the one tons but.... the one tons and 3/4 tons actually share most of the suspension components in the front end. That would leave be to believe that it will be the same to swap as a 1/2 ton.
|
|
|
|
|
08-29-2006, 04:15 PM
|
#4 |
|
RIP Mr Ron
Join Date: Dec 2005
Location: Big Sandy, Tn. 38221
Posts: 8,166
|
Re: Can this be done.
Thanks guys. I haven't messed with any 1 tons or 4wd stuff in a long time. Let the destruction begin.
__________________
Ron (Mr Round Tuit) Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket Last edited by Ron 586; 08-29-2006 at 04:15 PM. |
|
|
|
|
08-30-2006, 06:57 PM
|
#5 |
|
Registered User
Join Date: Feb 2004
Location: Tacoma WA
Posts: 1,365
|
Re: Can this be done.
Ron - If your frame is a 67 1T you will probably have to dimple it to fit a PS box. Heat and a BFH will do the job. I have yet to see a 67 frame (1/2, 3/4 or 1) that had a dimple to fit the PS box.
__________________
67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow |
|
|
|
|
08-31-2006, 08:58 PM
|
#6 |
|
RIP Mr Ron
Join Date: Dec 2005
Location: Big Sandy, Tn. 38221
Posts: 8,166
|
Re: Can this be done.
Thanks Bob, now that I'm ready to try to save it I have 2 people trying to buy it. Strange.
__________________
Ron (Mr Round Tuit) Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
