needle in a hay stack??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dougs69c10 · 09-10-2006, 04:13 PM

Finding a factory gas pedal assembly that still has the pedal on it? Everyone I look at for my 69 all have the pedal broken off.

Longhorn Man · 09-10-2006, 05:30 PM

it's a seperate piece, it snaps onto the floor.

dougs69c10 · 09-10-2006, 05:50 PM

Quote:

Originally Posted by Longhorn Man

it's a seperate piece, it snaps onto the floor.

where, b/c theres nothing on the floor where something/anythng would mount to

1969C/10 · 09-10-2006, 05:59 PM

There should be two little pieces of metal that stick up from the floor board and the pedal snaps into place on them. They should be right under where the pedal assembly ends.

jimmydean · 09-10-2006, 07:10 PM

It's 2 pins that the pedal never stays on. My pedal is under the seat somewhere because I got sick of puting it back on all the time.

Longhorn Man · 09-10-2006, 09:15 PM

The CST style rubber pedal is real bad about popping off, the plastic base model style is OK.
If your truck is a bit of a beater, you can drive screws through the flap on the bottom (base plastic style) and into the floor. it'll never fall off like this.
The studs should be to round balls, kind alooks like zerk (grease) fittings.

09-10-2006, 04:13 PM	#1
dougs69c10 Registered User Join Date: Feb 2006 Location: Birmingham,Alabama Posts: 260	needle in a hay stack??? Finding a factory gas pedal assembly that still has the pedal on it? Everyone I look at for my 69 all have the pedal broken off. __________________ 1969 c10 stepside 250 inline six, 4speed granny tranny, 4.11 posi rear end

09-10-2006, 05:30 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: needle in a hay stack??? it's a seperate piece, it snaps onto the floor.

09-10-2006, 05:59 PM	#4
1969C/10 Unskilled Labor Join Date: Jul 2006 Location: OH-IO Posts: 788	Re: needle in a hay stack??? There should be two little pieces of metal that stick up from the floor board and the pedal snaps into place on them. They should be right under where the pedal assembly ends. __________________ 1986 K/20, 350/TH400, My First 4x4.......

09-10-2006, 07:10 PM	#5
jimmydean Registered User Join Date: May 2005 Location: Beaverton, OR Posts: 3,728	Re: needle in a hay stack??? It's 2 pins that the pedal never stays on. My pedal is under the seat somewhere because I got sick of puting it back on all the time.

09-10-2006, 09:15 PM	#6
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: needle in a hay stack??? The CST style rubber pedal is real bad about popping off, the plastic base model style is OK. If your truck is a bit of a beater, you can drive screws through the flap on the bottom (base plastic style) and into the floor. it'll never fall off like this. The studs should be to round balls, kind alooks like zerk (grease) fittings.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.