![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Nov 2006
Location: St. Petersburg Florida
Posts: 23
|
Intake Manifold Gasket
I have a small Block 400 with a leaky intake manifold gasket. The leak has gotten bigger and I am wondering how much a repair is going to be. I do some work myself but with out much experience with this and no timing light I think it is over my head. what would something like this cost me to get repaired?
Here are pictures of my project, I have taken bumpers, emblems, trim, grill and lights off and am in the middle of taking the bed off |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: INtake Manifold Gasket
for the money it will cost you to take it in I would buy a gasket ($25) and a timing light ($50) and do it yourself. I put a new intake on mine and it's easy. Just be sure to titghten them down equally and take your time. I even installed ARP stainless steel bolts when i did mine...you will need to drain your coolent, remove your dizzy (good time to upgrade to HEI), remove intake, clean all surfaces, replace gasket, replace intake (use sealant on the bolts), replace dizzy, hook it all up and refill coolant. Let it all set up overnight and then start and reset timing. SHould be good..... I am sure that oyu can find detailed pictures on here that will fill in the blanks...
|
![]() |
![]() |
![]() |
#3 |
Account Suspended
Join Date: Oct 2004
Posts: 1,276
|
Re: INtake Manifold Gasket
I am sure I might start a little controversy on this subject, but definetly worth bringing up and comparing notes. In the past I have used the front and rear rubber lips for sealing the intake front and rear edge. I was careful putting them down and had no leaks. Now I have read and was told by the engine guru, to just lay down a good bead of silicone and forget the front and rear seals and you will be better off.
Any one care to throw out their opinions????? |
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: Jul 2004
Location: Estherville, Iowa
Posts: 3,371
|
Re: INtake Manifold Gasket
The end seals, imho, might be fine if the block has never been decked, heads have never been shaved, same thickness head gasket as stock and the stock intake manifold is used. If you change any of that, the stock end seals are going to either get squished too much or not enough causing leaks. If the clearance is too small, they will even prevent the intake from sealing to the heads. Even if they do fit right, it is just rubber on iron, and it will weep some oil out anyhow. A bead of Ultra-black rtv silicone is oil proof if done right and allows for any machining and other parts tolerance difference.
__________________
1968 C10 307 3spd Long Fleet ------ http://67-72chevytrucks.com/vboard/s...d.php?t=201103 1970 C10 305 Super T10 Long Fleet --- http://67-72chevytrucks.com/vboard/s...d.php?t=202285 1971 C20 383 TH350 Dana Posi ----- http://67-72chevytrucks.com/vboard/s...d.php?t=206894 2001 GMC Sierra 1500 C3 6.0 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Apr 2006
Location: Bellflower
Posts: 79
|
Re: INtake Manifold Gasket
When i did my intake, i also wasnt sure as to whether or not i was going to put the end seals in.. it had some pretty large gaps, i decided not to put them in, i just ran a good large bead of rtv and thats it. Still seems to be fine.. So no i dont think they are really necessary. I think you should do the intake yourself.. I was pretty fresh to motors and trucks when I did mine, and I decided to do the intake myself and it was easy cheese.. You will also need a torque wrench..
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: INtake Manifold Gasket
I couldn't fit a torgue wrench on my edelbrock...I seem to remember the instructions on Edelbrock webpage saying to use RTV instead of the rubber gasket, so i did. Like I said, let it cure overnight prior to starting your engine or you will have leaks from blowing the rtv out...
Last edited by msgross; 11-08-2006 at 04:28 PM. |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Apr 2006
Location: Bellflower
Posts: 79
|
Re: INtake Manifold Gasket
maybe use a swivel socket+extension? I think thats maybe what i did cant remember
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: INtake Manifold Gasket
they torque low anyway (20-30lbs maybe)? i used the two finger on a little wrench method!
|
![]() |
![]() |
![]() |
#9 |
Alright Alright Alright
Join Date: Mar 2004
Location: Midland, Texas
Posts: 1,672
|
Re: INtake Manifold Gasket
i have done 7 or 8 intake swaps and i always use the silicone and ditch the rubber end piece. i have never had a leak.
__________________
1972 Cheyenne Chevrolet red and white 357ci, Vortec heads, GM Performance high rise intake, Comp 268H .454/.454 218/218 110 LSA Quadrajet carb, Flowtech headers, 2.25 40 series HEI, Curve kit, TH 350, 3.07 gears 275/60/15s on 15x8 rallies |
![]() |
![]() |
![]() |
#10 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Re: INtake Manifold Gasket
You can do the intake gasket repair yourself without really needing to have a timing light handy. Just put a mark on the distributor where the rotor is pointing and a mark somewhere else to use as a reference - when you reinstall the distributor just make sure you get those marks lined up and you are good to go.
I did the intake on my BBC a while back and I was nervous that I would screw something up but really as long as you get the RTV laid down and set the intake down slowly so you don't have to move it - you should have no problems.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 Last edited by Yukon Jack; 11-08-2006 at 05:22 PM. |
![]() |
![]() |
![]() |
#11 |
Registered User
![]() Join Date: Oct 2006
Location: Southern Kalifornia
Posts: 3,066
|
Re: INtake Manifold Gasket
![]() ![]() |
![]() |
![]() |
![]() |
#12 |
sufficiently talented fool
![]() Join Date: Jun 2006
Location: Forest Hill, MD
Posts: 2,231
|
Re: INtake Manifold Gasket
20 years as a mechanic and I have always used silicone for the ends of the intake. Another tip for distributor removal/install. As said earlier, mark the distributor housing and rotor position. As you lift the distributor out, the rotor will spin. mark where it stops turning and use that mark as a reference when re installing the distributor.
__________________
"it's impossible to be surrounded by idiots when you are part of the circle" ![]() 2003 Suburban 2002 Pontiac Montana 1981 Corvette 1966 Impala Convertible Click here to support the board |
![]() |
![]() |
![]() |
#13 | |
Account Suspended
Join Date: Sep 2005
Location: Monroe, WA
Posts: 3,814
|
Re: INtake Manifold Gasket
Quote:
![]() |
|
![]() |
![]() |
![]() |
#14 | |
Account Suspended
Join Date: Sep 2005
Location: Monroe, WA
Posts: 3,814
|
Re: INtake Manifold Gasket
Quote:
I've never had a problem when I've used the seals, but I don't do it any more. The reason you've had good luck is because you're being very careful about placing the intake....it only takes a little shift to move it out of position. The 1/4" bead of RTV is just easier and more tolerant of a little "adjustment" if required. So I agree with both of you...but I've found the RTV bead to be a better solution. |
|
![]() |
![]() |
![]() |
#15 | |
Account Suspended
Join Date: Sep 2005
Location: Monroe, WA
Posts: 3,814
|
Re: INtake Manifold Gasket
Quote:
![]() |
|
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Jun 2006
Location: WVa
Posts: 758
|
Re: Intake Manifold Gasket
rtv front and rear started it up right after we got it put on ........no leaks
Shane |
![]() |
![]() |
![]() |
#17 |
Account Suspended
Join Date: Oct 2004
Posts: 1,276
|
Re: Intake Manifold Gasket
Reminds me of a bad experience my friend had with a local shop who did a manifold change for him. He drove it home, maybe 10 miles and to work the next day, maybe another 10 miles , and a rod was a knockin with a good sound motor with maybe 60k on it.
The shop refused to have anything to do with it. He took it to the GM boys and they found anti freeze in the crankcase!! Turns out the first shop must have not changed the oil after they spewed Prestone in the guys engine!!!! Be Sure to drain the coolant out. And change the oil too!!!! |
![]() |
![]() |
![]() |
#18 |
Account Suspended
Join Date: Oct 2004
Posts: 1,276
|
Re: Intake Manifold Gasket
I forgot to tie it together here, but I have read that if coolant gets in the crankcase and it runs it through the lube system, the only cure is a teardown and new bearings since the anti freeze eats the bearing material fast!!!!
![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|