|
03-21-2007, 07:26 AM
|
#1 |
|
Registered User
Join Date: Jun 2006
Location: Alabama
Posts: 54
|
poly gas tank install
Whos got pictures of installing poly gas tank, bought one has no instructions in it! under frame set up on 67 panel. HELP!!!!!
|
|
|
|
03-22-2007, 12:06 AM
|
#2 |
|
Its a Truck Thing......
Join Date: Dec 2004
Location: Sierra Vista, Arizona
Posts: 3,179
|
Re: poly gas tank install
I have one installed in a truck, will that help?
Smitty
__________________
71 C10 283/3SPD Full Resto 71 GMC 1500 Sierra Grande http://67-72chevytrucks.com/vboard/s...d.php?t=518599 70 C10 Suburban Former military GSA truck. 72 Chevy Blazer 4X4, Sloppy Jo, Mountain Climber. Wife says no more trucks. http://67-72chevytrucks.com/vboard/s...d.php?t=707378 72 GMC 1 Ton Motor Home, wife said no more trucks until she saw this one. Gen 3 6.0/4L80E 4.10 http://67-72chevytrucks.com/vboard/s...d.php?t=761110 68 GMC Suburban was 3/4 ton, now 1/2.Wife shook her head 71 C30 Wrecker 71 C20 Scott-Bilt As weird as it gets..BB Cheyenne AC Truck 68 GMC Long Stepside. They keep following me home 69 C30 Former Motor Home, Flat Bed time 70 G20 Red-E-Kamp Conversion "I'm your Boogy Van" |
|
|
|
|
03-23-2007, 10:10 PM
|
#3 |
|
Big Block
Join Date: Mar 2005
Location: Durham, N.C.
Posts: 1,649
|
Re: poly gas tank install
Did you remove your old steel tank? Do you have a new sending unit? Do you have the tank straps? It will install like a suburban or blazer tank. The panel has wood floor like suburban. I have a 72 Blazer tank out, what pictures do you need?
|
|
|
|
|
03-26-2007, 12:39 PM
|
#4 |
|
Registered User
Join Date: Jun 2006
Location: Alabama
Posts: 54
|
Re: poly gas tank install
Original tank is out,replacing with poly tank, straps and sending unit came with tank,when i put tank where old tank was the straps dont line up with any existing holes, and the straps dont secure the top of tank,they just go under it,it would allow tank to bounce around ,surely they dont expect you to mount it against the wood floor?
|
|
|
|
|
03-29-2007, 03:07 AM
|
#5 |
|
Registered User
Join Date: Jan 2007
Location: quartz hill
Posts: 20
|
Re: poly gas tank install
I AM LOOKING INTO DOING THE SAME SWAP OUT..I'VE HAD TO CHANGE SENDING UNIT TWICE ALREADY..IT COSTS ABOUT $70.00 FOR PART $200.00 FOR COMPLETE KIT (TANK,STRAPS,SENDING UNIT ,ETC)ALSO GONNA CUT AN ACCESS HOLE IN FLOOR BOARD ABOVE TANK FOR FUTURE ACCESS...
__________________
   STEEEVO 69 BurB
|
|
|
|
|
03-30-2007, 01:02 PM
|
#6 |
|
Senior Member
 Join Date: Mar 2000
Location: Rockville,In. USA
Posts: 3,721
|
Re: poly gas tank install
I don't have any pics but I can tell you how it goes. You'll see a flange on either side of tank they rest againset the bottom of the frame overlaping the frame enough to keep it from hitting the bottom of the floor, the j-bolts get hooked in the passenger outside vertical portion of the frame with the straps at the bottom strech the straps under tank and back up towards frame on opposite side and you'll see 2 holes in the frame, since you don't have any original tank parts you'll need to get 2 bolts, washers & nuts for use on this side of the frame, other than that before doing install get your sender installed and locate all your vent hoses and your filler hose thats needed and see if they are cracked if so replace them and myself I also replace the clamps, the 1 1/4" filler hose I've gotten at farm implement stores, marine outlets and occasionally NAPA, the vent hoses are available everywhere.
Hope this helps. GMCPaul |
|
|
|
|
03-30-2007, 01:07 PM
|
#7 |
|
Registered User
Join Date: Oct 2006
Location: Daytona, FL
Posts: 80
|
Re: poly gas tank install
Here is the site for how to install the gas tank from the Brother's website.
http://www.brotherstrucks.com/techar...NSTALLATION%20 |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
