Powertrax No Slip locker - The 1947 - Present Chevrolet & GMC Truck Message Board Network

redhead69 · 04-14-2008, 12:39 AM

Bought the unit in march and had a shop install my new 3.73 gears and this unit. Something was noticeably wrong right away (2 runs down the 1/4), brought the truck home and removed the unit. It had a broken spacer.. Contacted Richmond gear and sent the unit to warranty department to inspect. They said it was installed incorrectly breaking the spacer and sent me a replacement part along with a new spring kit and is good to go. I am trying to run for points in the street bracket and couldnt waste time with the truck down so I installed a mini spool. So here it is for sale with the warranty inspection notes, claim #s etc for 375.00 shipped to the lower 48, more anywhere else. This is just over 100 bucks off what I just paid for it not including shipping. Reply to this thread with questions..
The summit part # is PWT-92-0788-3005

Thanks
eric

redhead69 · 04-19-2008, 02:46 AM

ttt.
http://cgi.ebay.com/ebaymotors/ws/eB...ksid=p3907.m29
I will knock off 10% for members

redhead69 · 04-21-2008, 09:56 PM

Open to offers or trades

71chevytruckguy · 04-22-2008, 07:26 AM

well i got some stuff layin around. what are you needin? chris.

redhead69 · 04-23-2008, 02:22 AM

man where to start

Lowering springs, nitrous, good carbs and distributors, electric fan, Sbc go fast stuff, 3 pt seatbelts, 1st gen nova parts

71chevytruckguy · 04-23-2008, 04:28 AM

i got NIB edelbrock performer RPM intake for sbc, a new 15" electric fan, NIB auto trans cooler, re-man points distributors with about 100 miles on it, some muncie 4-speed parts, and probably some other stuff. any of that sound good? chris.

redhead69 · 04-23-2008, 04:58 AM

I could use the intake and what kind of electric fan is it.. any specs? I need a pretty good flowing fan to cool my 400sb.

71chevytruckguy · 04-24-2008, 06:19 AM

not to sure on the specs for the fan, let me do some research and ill get back to ya. chris.

71chevytruckguy · 05-02-2008, 06:04 AM

its a 16" torqflo. its the $70 one they sell at autozone. couldnt find any cfm specs. chris.

redhead69 · 05-02-2008, 06:45 AM

Sorry this sold pending payment to member truckmanloco.

71chevytruckguy · 05-06-2008, 07:21 PM

well dang. if it dont work, let me know. chris.

04-14-2008, 12:39 AM	#1
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Powertrax No Slip locker Bought the unit in march and had a shop install my new 3.73 gears and this unit. Something was noticeably wrong right away (2 runs down the 1/4), brought the truck home and removed the unit. It had a broken spacer.. Contacted Richmond gear and sent the unit to warranty department to inspect. They said it was installed incorrectly breaking the spacer and sent me a replacement part along with a new spring kit and is good to go. I am trying to run for points in the street bracket and couldnt waste time with the truck down so I installed a mini spool. So here it is for sale with the warranty inspection notes, claim #s etc for 375.00 shipped to the lower 48, more anywhere else. This is just over 100 bucks off what I just paid for it not including shipping. Reply to this thread with questions.. The summit part # is PWT-92-0788-3005 Thanks eric __________________ Currently truckless

04-19-2008, 02:46 AM	#2
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Re: Powertrax No Slip locker ttt. http://cgi.ebay.com/ebaymotors/ws/eB...ksid=p3907.m29 I will knock off 10% for members __________________ Currently truckless

04-21-2008, 09:56 PM	#3
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Re: Powertrax No Slip locker Open to offers or trades __________________ Currently truckless

04-22-2008, 07:26 AM	#4
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: Powertrax No Slip locker well i got some stuff layin around. what are you needin? chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

04-23-2008, 02:22 AM	#5
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Re: Powertrax No Slip locker man where to start Lowering springs, nitrous, good carbs and distributors, electric fan, Sbc go fast stuff, 3 pt seatbelts, 1st gen nova parts __________________ Currently truckless

04-23-2008, 04:28 AM	#6
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: Powertrax No Slip locker i got NIB edelbrock performer RPM intake for sbc, a new 15" electric fan, NIB auto trans cooler, re-man points distributors with about 100 miles on it, some muncie 4-speed parts, and probably some other stuff. any of that sound good? chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

04-23-2008, 04:58 AM	#7
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Re: Powertrax No Slip locker I could use the intake and what kind of electric fan is it.. any specs? I need a pretty good flowing fan to cool my 400sb. __________________ Currently truckless

04-24-2008, 06:19 AM	#8
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: Powertrax No Slip locker not to sure on the specs for the fan, let me do some research and ill get back to ya. chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

05-02-2008, 06:04 AM	#9
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: Powertrax No Slip locker its a 16" torqflo. its the $70 one they sell at autozone. couldnt find any cfm specs. chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

05-02-2008, 06:45 AM	#10
redhead69 fugedaboutit Join Date: Mar 2005 Location: Gresham, OR Posts: 832	Re: Powertrax No Slip locker Sorry this sold pending payment to member truckmanloco. __________________ Currently truckless

05-06-2008, 07:21 PM	#11
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: Powertrax No Slip locker well dang. if it dont work, let me know. chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.