The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-24-2008, 11:52 PM   #1
1969 k/10
Registered User
 
1969 k/10's Avatar
 
Join Date: Jun 2008
Location: Santa Rosa, California
Posts: 102
ball joints

For some reason i am having a tough time finding ball joints for my 1969 k/10.
At the local stores the guys are idiots and online i just can't seem to find any.
If anyone can give me a good site or some help i would greatly appreciate it.
Thank you.
1969 k/10 is offline   Reply With Quote
Old 06-25-2008, 12:06 AM   #2
Sequoyah
so easy a caveman can do it...
 
Sequoyah's Avatar
 
Join Date: May 2006
Location: Albuquerque, NM
Posts: 419
Re: ball joints

Check any of the board vendors and if all else fails...check here:

http://www.rockauto.com/
__________________
My build thread

http://67-72chevytrucks.com/vboard/s...d.php?t=242380
Sequoyah is offline   Reply With Quote
Old 06-25-2008, 12:13 AM   #3
ChevyDude
Senior Member
 
Join Date: Jun 2003
Location: Westminster, CO
Posts: 3,071
Re: ball joints

I did a search at http://www.rockauto.com and also Advance Auto http://www.advanceautoparts.com/ found that the K-10 and the C-10 are the same part numbers. However advance only lists the upper ball joint for the K-10. But check the part number and if you go back to Rock Auto link punch in all the info except use C-10....you will find the same part number for your K-10 listed at Advance Auto is listed for the C-10 at Rock Auto. So I am assuming the lower ball joint from a C-10 will work for you.
__________________
Alex


1971 Lil' Red 350 SBC 700R4

Last edited by ChevyDude; 06-25-2008 at 12:20 AM.
ChevyDude is offline   Reply With Quote
Old 06-25-2008, 12:16 AM   #4
1969 k/10
Registered User
 
1969 k/10's Avatar
 
Join Date: Jun 2008
Location: Santa Rosa, California
Posts: 102
Re: ball joints

Quote:
Originally Posted by ChevyDude View Post
I did a search at http://www.rockauto.com and also Advance Auto found that the K-10 and the C-10 are the same part numbers. However advance only lists the upper ball joint. But check the part number and if you go back to Rock Auto link punch in all the info except use C-10....you will find the same part number for your K-10 listed for the C-10. So I am assuming the lower ball joint from a C-10 will work for you.
so 4 wheel and 2 wheel drive ball joints are the same?
1969 k/10 is offline   Reply With Quote
Old 06-25-2008, 12:22 AM   #5
ChevyDude
Senior Member
 
Join Date: Jun 2003
Location: Westminster, CO
Posts: 3,071
Re: ball joints

Quote:
Originally Posted by 1969 k/10 View Post
so 4 wheel and 2 wheel drive ball joints are the same?
Check the part numbers as I did....it sure appears that they are the same...at least for the upper ones. I can't find the lower ones listed . You could remove your lower ball joint run a caliper on it ..go down to the local parts house ask for a C-10 and measure it.

Here is the upper ball joint part # listed at Advance for a K-10 Part Number: K6024 Its listed at Rock Auto for a 69 C-10.
__________________
Alex


1971 Lil' Red 350 SBC 700R4

Last edited by ChevyDude; 06-25-2008 at 12:25 AM.
ChevyDude is offline   Reply With Quote
Old 06-25-2008, 03:45 AM   #6
70rs/ss
Registered User
 
70rs/ss's Avatar
 
Join Date: Dec 2004
Location: Northern AZ
Posts: 7,270
Re: ball joints

Are there ball joints on a closed knuckle 4X?? I know it may be a dumb question, but I think 69 was a drum brake closed knuckle front end and I don't knoe if they had a conventional ball joint??
70rs/ss is offline   Reply With Quote
Old 06-25-2008, 03:51 AM   #7
70rs/ss
Registered User
 
70rs/ss's Avatar
 
Join Date: Dec 2004
Location: Northern AZ
Posts: 7,270
Re: ball joints

I had to check myself cause I wasn't sure, but YA, there aren't ball joints in a closed knuckle dana 44 front axle, so if your axle is the OE from 69, you don't have any!! Here is a quote from a site I googled!!


This page will be about the closed knuckle 44.

The Dana 44 closed knuckle is known to be weaker than the open knuckle one. This is probably why they stopped using it in the early 70's. The differences between it and the open knuckle are very easy to spot.

First off the knuckles are really different.



These are the drivers and passenger side knuckles from the top side. These knuckles do not use ball joints like newer 44's. The driver side has a bronze bushing in the top end and a cone bearing in the bottom. These are shimmed for tightness. The passenger side is the same but with 2 bearings and no bronze bushing. The 4 blots on the top of the passenger side knuckle are what is holding the bearing in place. You will find the same thing on the bottom. The drivers side 4 bolts hold on the steering arm that holds the bushing in place.
70rs/ss is offline   Reply With Quote
Old 06-25-2008, 05:46 AM   #8
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
Re: ball joints

I walked into my local Napa store and walked out with a set last week.They were sitting on the shelf.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 07-01-2008, 01:31 AM   #9
1969 k/10
Registered User
 
1969 k/10's Avatar
 
Join Date: Jun 2008
Location: Santa Rosa, California
Posts: 102
Re: ball joints

So i have no replacement ball joints?
I tried 2 more stores in town and none of them had any or could even find them =(
1969 k/10 is offline   Reply With Quote
Old 07-02-2008, 01:55 AM   #10
1969 k/10
Registered User
 
1969 k/10's Avatar
 
Join Date: Jun 2008
Location: Santa Rosa, California
Posts: 102
Re: ball joints

any help?
__________________
1969 red k/10 with sb350
4.11 gear ratio, front disk, 3 speed automatic
1969 k/10 is offline   Reply With Quote
Old 07-02-2008, 09:41 AM   #11
jerry moss
Born Psycho
 
jerry moss's Avatar
 
Join Date: Feb 2001
Location: brentwood,cal,usa
Posts: 4,936
Re: ball joints

if it still has a closed knuckle axle, it doesn't have ball joints. it looks more like a small version of the "kingpin" style of the dana 60. why not swap out the whole axle for a disc brake differential. any axle from 71-87 will bolt in (71-91 on blazer and suburban). just match your gear ratio and a little bit of brake system mods and you are good to go. i have a 10 bolt from an 80s blazer with 3:08s that i'll give you free if you want to swap it in. back when i had my 69 K/10 the first thing i swapped was the front axle, 2nd was installing a 205 in place of the rockwell.
by the way,C series and K series DO NOT use the same ball joints.
__________________
jerry moss
72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD
69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies.
73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog.
77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW
BRENTWOOD,CALIFORNIA
jerry moss is offline   Reply With Quote
Old 07-02-2008, 02:23 PM   #12
1969 k/10
Registered User
 
1969 k/10's Avatar
 
Join Date: Jun 2008
Location: Santa Rosa, California
Posts: 102
Re: ball joints

Quote:
Originally Posted by jerry moss View Post
if it still has a closed knuckle axle, it doesn't have ball joints. it looks more like a small version of the "kingpin" style of the dana 60. why not swap out the whole axle for a disc brake differential. any axle from 71-87 will bolt in (71-91 on blazer and suburban). just match your gear ratio and a little bit of brake system mods and you are good to go. i have a 10 bolt from an 80s blazer with 3:08s that i'll give you free if you want to swap it in. back when i had my 69 K/10 the first thing i swapped was the front axle, 2nd was installing a 205 in place of the rockwell.
by the way,C series and K series DO NOT use the same ball joints.
Ya it has a 205 in it and the front already has discs. Does that meen i shuld be looking for the year of the discs for my ball joints????
__________________
1969 red k/10 with sb350
4.11 gear ratio, front disk, 3 speed automatic
1969 k/10 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:39 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com