The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-04-2009, 05:52 PM   #1
lumpyguy
Registered User
 
Join Date: Mar 2008
Location: london ontario
Posts: 62
welding heater control

I am looking to attach my heater control leaver to the cast chrome housing but there is no way to re-attach it and I was going to do a small tig weld on what was left of the rivot but does anyone know what the cast material is
made out of any help would be great
lumpyguy is offline   Reply With Quote
Old 01-04-2009, 06:34 PM   #2
PanelDeland
I am a Referee of life.
 
PanelDeland's Avatar
 
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,992
Re: welding heater control

It's called "pot metal".I really don't know if you can TIG it.I doubt it but it never hurts to try.If it doesn't work they make a kit to repair the broken levers.It's made of steel.They only take a couple hours to install and from what I can tell they will never break again.In order to make sure you have a good repair remove the cables and clean/lube them so they operate smoothly.I cleaned mine in a parts washer and then laid them in my oil drain pan where I had left oil.It's been 6-7 years and they still work well.I do spray some graphite lube in the ends of the cables regularly.
BTW Any vendor should carry the kit.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion.
You can't fix stupid,not even with duct tape.
"My appearance is due to the fact that "GOD" does punish you for having too much fun!"
Barrett-Jackson has perfected alchemy,they make rust into gold!
"You can lead a horse to water but you can't saddle a duck"
"Cleverly disguised as a 'Responsible Adult'
"Sometimes your Knight in shining armor is just a retard in tinfoil"

Last edited by PanelDeland; 01-04-2009 at 06:35 PM.
PanelDeland is offline   Reply With Quote
Old 01-04-2009, 06:43 PM   #3
dave2953
Dave's not here, man
 
dave2953's Avatar
 
Join Date: Jun 2004
Location: Winder, Georgia
Posts: 2,000
Re: welding heater control

I agree with Panel. Mine broke off and I thought about trying to have it welded too. In the end I just replaced it. It didn't cost very much and wasn't too hard to do. If you do decide to weld it let us know how it works out for you.
__________________
- 2014 VW Jetta
- 2015 VW Jetta
- 1966 Ford F-250
dave2953 is offline   Reply With Quote
Old 01-05-2009, 12:59 PM   #4
KEL
72 GMC
 
KEL's Avatar
 
Join Date: Feb 2008
Location: Wells, Maine
Posts: 534
Re: welding heater control

http://67-72chevytrucks.com/vboard/s...d.php?t=245558

this should help
good luck
KEL is offline   Reply With Quote
Old 01-05-2009, 10:35 PM   #5
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,774
Re: welding heater control

-
I get the impression that he is talking about the chrome face coming loose from the lever assembly.... If this is correct, you won't be able to weld it because it is pot metal as Panel said, and has a low melting point and it will just "blow" away. I have repaired these by drilling through the face of the unit, countersinking the holes on the outside, putting small flat head bolts in it and getting a new self stick metallic decal for the face.

LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 01-05-2009, 10:50 PM   #6
cdowns
Senior Member
 
cdowns's Avatar
 
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
Re: welding heater control

i've drilled and tapped and used a screw for repairing the levers had them work for years without problems
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane

MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF

DONT BELIEVE EVERYTHING YOU THINK

TAKE MY ADVISE;I DON'T USE IT ANYWAY
cdowns is offline   Reply With Quote
Old 01-05-2009, 11:32 PM   #7
j_cst_10
Registered User
 
j_cst_10's Avatar
 
Join Date: Nov 2008
Location: Cleveland, OH
Posts: 592
Re: welding heater control

You can try tig welding it with no filler rod, or try brazing which would be plenty strong.
j_cst_10 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:16 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com