Post Your 60-63 Body Style Chevy/GMC Trucks - Page 6 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1Bad62Pro/Street · 05-15-2009, 04:13 PM

7.580 @ 89.7 - 1/8 mile is not bad!
How do ya have her set up?
Enigine/Tranny
Front end/Rear End
10.5 Slicks?
Etc.

Bears63 · 05-15-2009, 05:30 PM

Here's a couple pics of my '63 C20:

Super73 · 05-16-2009, 04:41 AM

Well its got:

347ci LS1
Forged roatating assembley
Ported factory heads
243/250 @ .050 cam
Thise passes had an LS6 intake with a factory smoothed and ported TB
Had a factory mechanical water pump
Underdrive crank pulley
Manual steering box
Power brakes

4L80E trans
4,900rpm converter
3.73
30" x 14.50 ET Street (going through the traps in second gear with the converter locked aprox 7,100rpm)

Being all steel, the truck weighed in a 3,840 with me in the seat and 1/2 tank of gas.

The front suspension is stock minus the springs and shocks. According to Moroso, I was running a spring that would not work for the weight of my truck. But, according to the leverage ratio and my unsprung weight, I found it to be ummm, perfect

Shocks were a Comp Engineering 3-way, but even on the 70/30 setting, there was still a little too much stored energy in the front. I have switched to a Rancho 9,000x.

The rear again is stock other than an adjustable lower control arm braket I made that allows you to move the mounting location, I think there are 5 holes. Also a Classic performance lowering spring, blocks and again a Comp 3-way shock.

Since that outing I have:

Switched to a single plain with a dominator throttle body
Removed the factory bench seat for a set of light weight buckets (50lbs)
Build a new front crossmember that retains the factory control arms (25lbs, but the intake/N20 plate and TB made up the difference)
Cutting off the 30-40lb tow hith I once welded on it
Putting a factory weight tailgate on it (had an extrat junk gate so I added about 100lbs to it)
Just received a 1 piece glass front end (75 lbs vs te 240 the factory stuff weighs)
Put a 4.56 gear in it
Put an electric water pump on it
Pray every night it goes 11.40-11.50 NA in the 1/4 and low 10's on the jug...

Chuck78 · 05-16-2009, 09:49 AM

sounds awesome, I'm very impressed - wish I had some LS1's for my 63 panel and my 71 Camaro...

1Bad62Pro/Street · 05-17-2009, 02:36 PM

Same here. Kinda glad I have a that 1970 LS9 350ci/355 vette motor in my ole' 62 truck. The block and heads are Nostalgia and kinda rare now.

SPECS:
BLOCK
Casting #
(1969-79)
3970010
350
4 Bolt Main
Vette
370 HP

HEADS
Casting #
3927186
302/327/350
Intake
2.02
Exaust
1.6

1Bad62Pro/Street · 06-05-2009, 11:15 PM

Heck Yeah!
ROAST THE TIRES SLAP OFF!
POST'EM IF YA ROAST'EM FELLAS!!!!!

YouTube - 1960 chevy drag truck

Super73 · 06-06-2009, 12:37 PM

Something like this? This is my old truck.. Well, half of it any way.. Kept the 63 frame which is what y sheetmetal is riding on right now.

Tires were a litle old and I had a set of BFG drag radials on the way..

TwoFiftyShifter · 06-06-2009, 01:09 PM

You always gotta get 'em hot once more before they come off!

1Bad62Pro/Street · 06-06-2009, 01:36 PM

Super73......................

THAT'S WHAT I'M TALKING ABOUT!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
YOU HAVE GOT IT IN YOUR VEINS TOO.................................................
WE THINK ALIKE!!!!!!!!!!!!

YouTube - Wheel Stand Contest

1Bad62Pro/Street · 06-06-2009, 01:39 PM

Delete

**scotts62** · 06-06-2009, 06:24 PM

i bet that landing hurt just a bit and not just the truck..

61chev1tondually · 06-06-2009, 07:03 PM

i have three old chevs and gmcs. i have a wrecked gmc shortbox(62),a orange stepside shortbox(63) and a blue 1 ton dually chev (61) heres some pics of the blue one and orange one(ill have pics of the dually soon!)

61chev1tondually · 06-06-2009, 07:11 PM

these trucks are like the best old trucks from the sixties

63sbssbbw · 06-06-2009, 11:21 PM

Welcome 61,from the other side
Cool stuff
What are your plans for them all?
I heard that you may have gotten some snow today!!
T

1Bad62Pro/Street · 06-07-2009, 03:07 PM

Quote:

Originally Posted by scotts62

i bet that landing hurt just a bit and not just the truck..

Oh yea.......
Maybe tore a new one......ha ha
I'd do it for $20,000 green stamps!!!!!!!!!!!!!
Lord willing I hope to take my dad here the next The Playground of Power.........Father and Son "ON THE BACK BUMPER" Bonding!!!!!!
OCTOBER-Sat 3rd- 2009 World Power Wheel Standing Championships
Check this out:
http://www.outlawracing.com/MESSAGEF...c/Default.aspx
World Power Wheelstanding Championships - $20,000 To Win!

YouTube - 2008 Byron Wheelstanding Championships...

Byron Dragway http://www.byrondragway.com/Home.html is a 1/4 mile dragstrip located in Byron, IL, about 1.5 hours from Chicago. It was originally opened in the 1960s. It was most known for running cars 4 at a time in the past, but this practice has been discontinued. For that reason, Byron is a comparatively wide track. It is currently best know for the World Power Wheel Standing
http://www.byrondragway.com/2009_Byr...y_Schedule.pdf

Super73 · 06-07-2009, 03:12 PM

The problem I have with that is you are not garuanteed the coin. I have a lot of money in my junk even though it still looks like junk, I'd hate to have to buy things a second time around. Cool to watch though..

**scotts62** · 06-07-2009, 03:18 PM

Yeah its more fun to watch someone else tear their stuff up

1Bad62Pro/Street · 06-07-2009, 03:58 PM

I hear ya buds...........
If had more money than since I'd do it........
I just have a few cents..

So I'll just have fun watching those fellas tuck and roll!!!!!!!!!!!!!!!!!!!!!
Like the Duke Boys always said, "Keep her between the ditches!"

61chev1tondually · 06-07-2009, 10:07 PM

hey 63 thanks for the welcome. the blue one i am looking 4 another shortbox chassis (i found one but the guy aint ready to give it up just yet) so it sitting around, and the orange one is my aunties. i plan to hope fully get the blue one done before i graduate from school nxt yr, so i can use it for grad. haha

1Bad62Pro/Street · 06-08-2009, 05:24 AM

Keep the Pictures coming guys!
Keep us updated of your progress...........

**GruntMoanCough** · 06-08-2009, 03:00 PM

Hi RMH

Quote:

Originally Posted by 63sbssbbw

I heard that you may have gotten some snow today!!
T

Still waitin' for the snow to melt here..................

**scotts62** · 06-08-2009, 07:43 PM

^^ Yeah that sucks..

65GMCShortStep · 06-08-2009, 11:15 PM

New here, just bought the truck last Wednesday, haven't really had a chance to do anything yet but here we go.

61chev1tondually · 06-09-2009, 10:56 PM

hi BC how r ya? all the snow left here 3 days ago(yay!) good luck on your project truck too dude. hope the snow melts soon 4 ya

bobjob · 06-10-2009, 12:30 PM

looks like someone forgot there wheelie bars.. a lot of money to end up on your back like a turtle...

05-15-2009, 04:13 PM	#126
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: Post Your 60-63 Body Style Chevy/GMC Trucks 7.580 @ 89.7 - 1/8 mile is not bad! How do ya have her set up? Enigine/Tranny Front end/Rear End 10.5 Slicks? Etc. __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D.

05-15-2009, 05:30 PM	#127
Bears63 ...just another truck junkie.. Join Date: May 2009 Location: Watertown, SD Posts: 698	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Here's a couple pics of my '63 C20: __________________ Mike "Bear" Shea

05-16-2009, 04:41 AM	#128
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Well its got: 347ci LS1 Forged roatating assembley Ported factory heads 243/250 @ .050 cam Thise passes had an LS6 intake with a factory smoothed and ported TB Had a factory mechanical water pump Underdrive crank pulley Manual steering box Power brakes 4L80E trans 4,900rpm converter 3.73 30" x 14.50 ET Street (going through the traps in second gear with the converter locked aprox 7,100rpm) Being all steel, the truck weighed in a 3,840 with me in the seat and 1/2 tank of gas. The front suspension is stock minus the springs and shocks. According to Moroso, I was running a spring that would not work for the weight of my truck. But, according to the leverage ratio and my unsprung weight, I found it to be ummm, perfect Shocks were a Comp Engineering 3-way, but even on the 70/30 setting, there was still a little too much stored energy in the front. I have switched to a Rancho 9,000x. The rear again is stock other than an adjustable lower control arm braket I made that allows you to move the mounting location, I think there are 5 holes. Also a Classic performance lowering spring, blocks and again a Comp 3-way shock. Since that outing I have: Switched to a single plain with a dominator throttle body Removed the factory bench seat for a set of light weight buckets (50lbs) Build a new front crossmember that retains the factory control arms (25lbs, but the intake/N20 plate and TB made up the difference) Cutting off the 30-40lb tow hith I once welded on it Putting a factory weight tailgate on it (had an extrat junk gate so I added about 100lbs to it) Just received a 1 piece glass front end (75 lbs vs te 240 the factory stuff weighs) Put a 4.56 gear in it Put an electric water pump on it Pray every night it goes 11.40-11.50 NA in the 1/4 and low 10's on the jug... __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 Last edited by Super73; 05-16-2009 at 04:43 AM.

05-16-2009, 09:49 AM	#129
Chuck78 Registered User Join Date: Apr 2005 Location: Columbus, OH Posts: 197	Re: Post Your 60-63 Body Style Chevy/GMC Trucks sounds awesome, I'm very impressed - wish I had some LS1's for my 63 panel and my 71 Camaro... __________________ Chuck in Ohio 1962 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 75-87/91 disc brake front end* 1988 Suzuki Samurai 4x4 project, VW 1.9L mTDI, Toyota R151F transmission & Toyota full floater axles, LWB body tub stretch project* Many 1977-1979 Suzuki GS motorcycles, Kawasaki KDX220R, '77 Suzuki PE250, etc Last edited by Chuck78; 05-16-2009 at 09:49 AM.*

05-17-2009, 02:36 PM	#130
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Same here. Kinda glad I have a that 1970 LS9 350ci/355 vette motor in my ole' 62 truck. The block and heads are Nostalgia and kinda rare now. SPECS: BLOCK Casting # (1969-79) 3970010 350 4 Bolt Main Vette 370 HP HEADS Casting # 3927186 302/327/350 Intake 2.02 Exaust 1.6 __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D.

06-06-2009, 12:37 PM	#132
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Something like this? This is my old truck.. Well, half of it any way.. Kept the 63 frame which is what y sheetmetal is riding on right now. Tires were a litle old and I had a set of BFG drag radials on the way.. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

06-06-2009, 01:09 PM	#133
TwoFiftyShifter Registered User Join Date: Nov 2008 Location: Gwinnett GA Posts: 1,803	Re: Post Your 60-63 Body Style Chevy/GMC Trucks You always gotta get 'em hot once more before they come off! __________________ 1982 K10 SWB 1987 V20 - Sold - Doh! Last edited by TwoFiftyShifter; 06-06-2009 at 01:10 PM.

06-06-2009, 01:39 PM	#135
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Delete __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D. Last edited by 1Bad62Pro/Street; 06-06-2009 at 01:41 PM. Reason: DELETE

06-06-2009, 06:24 PM	#136
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Post Your 60-63 Body Style Chevy/GMC Trucks i bet that landing hurt just a bit and not just the truck.. __________________ Scott 93 crew cab build Project 62

06-06-2009, 07:03 PM	#137
61chev1tondually Registered User Join Date: Jun 2009 Location: Rocky Mountain House, Alberta Posts: 6	Re: Post Your 60-63 Body Style Chevy/GMC Trucks i have three old chevs and gmcs. i have a wrecked gmc shortbox(62),a orange stepside shortbox(63) and a blue 1 ton dually chev (61) heres some pics of the blue one and orange one(ill have pics of the dually soon!) Attached Images

06-06-2009, 07:11 PM	#138
61chev1tondually Registered User Join Date: Jun 2009 Location: Rocky Mountain House, Alberta Posts: 6	Re: Post Your 60-63 Body Style Chevy/GMC Trucks these trucks are like the best old trucks from the sixties

06-06-2009, 11:21 PM	#139
63sbssbbw UCA63 Join Date: Aug 2005 Location: Lloydminster AB Can. Posts: 1,637	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Welcome 61,from the other side Cool stuff What are your plans for them all? I heard that you may have gotten some snow today!! T __________________ member#7816 "63 sb ss bbw 350\350 12 bolt rear Pwr Fr Disc PS tilt '61 GMC in progress '63 GMC to use for parts '90 Chevy Ext cab sbfs 5.7l (current d d)

06-07-2009, 03:12 PM	#141
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Post Your 60-63 Body Style Chevy/GMC Trucks The problem I have with that is you are not garuanteed the coin. I have a lot of money in my junk even though it still looks like junk, I'd hate to have to buy things a second time around. Cool to watch though.. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

06-07-2009, 03:18 PM	#142
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Yeah its more fun to watch someone else tear their stuff up __________________ Scott 93 crew cab build Project 62

06-07-2009, 03:58 PM	#143
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: Post Your 60-63 Body Style Chevy/GMC Trucks I hear ya buds........... If had more money than since I'd do it........ I just have a few cents.. So I'll just have fun watching those fellas tuck and roll!!!!!!!!!!!!!!!!!!!!! Like the Duke Boys always said, "Keep her between the ditches!" __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D.



Register or Log In To remove these advertisements.

06-07-2009, 10:07 PM	#144
61chev1tondually Registered User Join Date: Jun 2009 Location: Rocky Mountain House, Alberta Posts: 6	Re: Post Your 60-63 Body Style Chevy/GMC Trucks hey 63 thanks for the welcome. the blue one i am looking 4 another shortbox chassis (i found one but the guy aint ready to give it up just yet) so it sitting around, and the orange one is my aunties. i plan to hope fully get the blue one done before i graduate from school nxt yr, so i can use it for grad. haha Last edited by 61chev1tondually; 06-07-2009 at 10:08 PM.

06-08-2009, 05:24 AM	#145
1Bad62Pro/Street "Where were you in '62?" Join Date: Jul 2004 Location: Cleveland County, North Cackalacky Posts: 5,013	Re: Post Your 60-63 Body Style Chevy/GMC Trucks Keep the Pictures coming guys! Keep us updated of your progress........... __________________ PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D.

06-08-2009, 07:43 PM	#147
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Post Your 60-63 Body Style Chevy/GMC Trucks ^^ Yeah that sucks.. __________________ Scott 93 crew cab build Project 62

06-08-2009, 11:15 PM	#148
65GMCShortStep Registered User Join Date: Jun 2009 Location: Clackamas, OR Posts: 14	Re: Post Your 60-63 Body Style Chevy/GMC Trucks New here, just bought the truck last Wednesday, haven't really had a chance to do anything yet but here we go. Attached Images

06-09-2009, 10:56 PM	#149
61chev1tondually Registered User Join Date: Jun 2009 Location: Rocky Mountain House, Alberta Posts: 6	Re: Post Your 60-63 Body Style Chevy/GMC Trucks hi BC how r ya? all the snow left here 3 days ago(yay!) good luck on your project truck too dude. hope the snow melts soon 4 ya

06-10-2009, 12:30 PM	#150
bobjob Registered User Join Date: May 2009 Location: florence arizona Posts: 53	Re: Post Your 60-63 Body Style Chevy/GMC Trucks looks like someone forgot there wheelie bars.. a lot of money to end up on your back like a turtle...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.