![]() |
![]() |
#1 |
Registered User
Join Date: Mar 2003
Location: San Antonio, TX
Posts: 441
|
removing cab trim?
Guys, i have a 77 silverado, and want to remove the trim that goes around the rear of the cab. i don't want to destroy it though, since after the body work and paint, I want to put it back on. Does it have any special fittingss or steps to remove it? I don't want to practice on 1 in the junkyard, since that might mess it up for someone who needs it. Any help here?
![]() |
![]() |
![]() |
![]() |
#2 |
been here longer than Liz
Join Date: Feb 2000
Location: Broken Arrow, OK
Posts: 2,437
|
I just popped my corners off, didn't damage them at all. Then you can slide the long back piece off. You'll have to buy new mounting tabs since more than likely they'll break. Just go slow and watch the trim to make sure it's not about to crack or bend. Good luck!
__________________
~Greg~ Mac's Garage '87 SWB 6/8 drop "Piso" '08 CCSB Silverado DD the departed '89 GMC K5 Jimmy 4x4 "Rusty Nuts" '77 Chevy K5 Blazer 2wd '83 Chevy stepside "You get what you pay for" - Mike 'swervin ervin' Ervin |
![]() |
![]() |
![]() |
#3 |
Insert Witty Text Here
Join Date: Oct 2002
Location: San Antonio, TX
Posts: 3,415
|
Hey! Another guy in San Antonio...
Slonaker |
![]() |
![]() |
![]() |
#4 |
pkbinplano
Join Date: Nov 2002
Location: Plano Texas
Posts: 370
|
Yea don't damage them. They are worth their weight in gold. Hey Low 87 I think I'm going to either buy plastic corner bed trim or try to make some out of extra trim I have left over. Trying a heat gun to bend.
__________________
http://www.picturetrail.com/gallery/...7496&members=1 84 chevy silverado aka The Bananna Boat |
![]() |
![]() |
![]() |
#5 | |
Take it to the limit
Join Date: Mar 2003
Location: Manitoba, Canada
Posts: 145
|
if you reach up on the inside of thecab there is one 3/8 trim nut maybe 2 that holds the corner ones on.then slide the rear one out like LOW87 said.If you end up damaging one,i'm sure i got a couple of ding free ones around here,and i won't soak ya too bad for them
![]() Quote:
![]() ![]()
__________________
1995 GMC SLE Ext cab 4X4 Z-71 loaded daily driver 87 k25 Fully Loaded inc captain buckets and console,12" susp lift,3" body lift 42"swampers 66 Cutlass 2dr hardtop currently undergoing frame off 55 chev 2dr hardtop awaiting attention 85 Chev silverado 1/2 ton loaded,daily driver(stolen) 80 chev silverado 1/2 ton farm truck 87 S-jimmy V-8,lowered ,Parting out 49 Chev 1/2 parting out parting numerous 73-80 chev trucks 01 Polaris edge X (highly modified) 58 NSU Prima scooter awaiting total restoration Last edited by twistedmetal; 03-27-2003 at 08:06 PM. |
|
![]() |
![]() |
![]() |
#6 | |
been here longer than Liz
Join Date: Feb 2000
Location: Broken Arrow, OK
Posts: 2,437
|
Quote:
__________________
~Greg~ Mac's Garage '87 SWB 6/8 drop "Piso" '08 CCSB Silverado DD the departed '89 GMC K5 Jimmy 4x4 "Rusty Nuts" '77 Chevy K5 Blazer 2wd '83 Chevy stepside "You get what you pay for" - Mike 'swervin ervin' Ervin |
|
![]() |
![]() |
![]() |
#7 |
pkbinplano
Join Date: Nov 2002
Location: Plano Texas
Posts: 370
|
no but brandon will be
__________________
http://www.picturetrail.com/gallery/...7496&members=1 84 chevy silverado aka The Bananna Boat |
![]() |
![]() |
![]() |
#8 |
been here longer than Liz
Join Date: Feb 2000
Location: Broken Arrow, OK
Posts: 2,437
|
Alright, I'll give it to him to pass on to you. If making your own bed corners doesn't work, then you'll be halfway there.
__________________
~Greg~ Mac's Garage '87 SWB 6/8 drop "Piso" '08 CCSB Silverado DD the departed '89 GMC K5 Jimmy 4x4 "Rusty Nuts" '77 Chevy K5 Blazer 2wd '83 Chevy stepside "You get what you pay for" - Mike 'swervin ervin' Ervin |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|