Project NOT4SLE - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*vegaschevy* · 10-03-2009, 07:59 PM

Another week has gone by and I finally got back out to work on the truck. Installed a manual fuel pump, new water pump gaskets as one of them ripped with moving and tightening the new water pump on. And FINALLY SHE IS RUNNING.

Seems to run very strong. I wonder if 81k is original miles. the seat and pedals are not worn so maybe.

http://www.youtube.com/watch?v=MapcMuJHLTA

*highperf4x4* · 10-03-2009, 09:45 PM

nah you can tell a low mileage truck because it won't have oil/dirt buildup on the frame/engine/firewall, etc. But the engine may have been rebuilt or replaced at some point. As long as it runs strong is all that matter though eh? Be sure to run some ZDDP in your oil or some Valvoline VR1 to stretch your cam as far as possible.

VA72C10 · 10-03-2009, 10:03 PM

cool deal...congrats on getting the fuel issue figured out. Glad it was just the fuel pump...

DuramaxC10 · 10-03-2009, 11:38 PM

what happen to project Vegas is that the truck which got stole

*vegaschevy* · 10-05-2009, 12:23 AM

Quote:

Originally Posted by DuramaxC10

what happen to project Vegas is that the truck which got stole

no my daily driver was stolen.

Project Vegas got put on hold while i finish getting this one driving and in great looking condition.

I have a plan of powdercoating another SWB frame, installing air ride suspension and an LS motor. Then make it in to project Vegas.

On a side note I purchased a new Optima red top battery today for the truck in preparation of getting it in great running conditin. I am hoping the old battery was just old but who knows. It was not holding a charge. Ill install the red top and see what voltage output was.
I am cleaning the set belts probably on Tuesday and reinstalling them and the seat. Tomorrow I have to ship some doors after work and then go to sleep to head back to work

GRAVES rule. LOL

I am tickled pink to get this truck out of the Driveway and onto the road just to even drive her around the block.

*vegaschevy* · 10-05-2009, 12:24 AM

Quote:

Originally Posted by VA72C10

cool deal...congrats on getting the fuel issue figured out. Glad it was just the fuel pump...

It is really odd how on old vehicles you replace on part only to have another part have to be replaced as it goes bad as soon as the new part is installed.

VA72C10 · 10-05-2009, 12:32 AM

They are wallet eaters basically. As I get one thing checked off the list I think of three more I'd like to do "since I already went this far, I might as well......"

*highperf4x4* · 10-05-2009, 12:32 AM

Quote:

Originally Posted by vegaschevy

It is really odd how on old vehicles you replace on part only to have another part have to be replaced as it goes bad as soon as the new part is installed.

Yeah funny how that works huh?

good work dude.

*vegaschevy* · 10-05-2009, 12:40 AM

Quote:

Originally Posted by VA72C10

They are wallet eaters basically. As I get one thing checked off the list I think of three more I'd like to do "since I already went this far, I might as well......"

Well I wanted a little more then a 4/6 drop so I decided 7. instead of blocks and needing to route an exhaust I called porterbuilt up. Now I am htinking about air ride on my next ttruck. not to mention I want a daily driver air ride truck, a muscle truck and a 4x4 like the stock lifted red and white one on this board. I am not a purist when it comes to these trucks either. but that red/white with stock trim looks great!!!!

Quote:

Originally Posted by highperf4x4

Yeah funny how that works huh?

good work dude.

Thank you.

Cannot wait to get it driving thats for sure. This truck will be a "muscle truck" build per say... so I have another trick up my sleeve that started today as well...

Of course it is only more money!! Luckily i dont have a monthly car payment

*highperf4x4* · 10-05-2009, 12:41 AM

Well, just keep the pics coming

joe231 · 10-05-2009, 12:47 AM

I'm In!!
nice work!

nuke1 · 10-05-2009, 01:02 AM

Hey Deven, truck is coming along great, gonna turn out great, you gonna be around for sema, i will be there that week, as i am going for it!

*vegaschevy* · 10-05-2009, 01:09 AM

Quote:

Originally Posted by nuke1

Hey Deven, truck is coming along great, gonna turn out great, you gonna be around for sema, i will be there that week, as i am going for it!

Yes sir, AM always here for Sema... hunting starts the next week. Besides it is a week very hectic at work and so we do not get days off and are authorized to work 7 straight days that week.

DuramaxC10 · 10-05-2009, 07:21 AM

do you still have project Vegas

*vegaschevy* · 10-06-2009, 04:54 PM

Quote:

Originally Posted by DuramaxC10

do you still have project Vegas

Project Vegas will be starting from scratch. plans have changed a bit with her as I do up htis daily driver. i am starting with a powdercoated chassis that will be porterbuilt Air ride. It will be super clean and not sure all the details. I know for sure it will be an LS2 set up. I want to do up a SUPER clean daily driver.

*vegaschevy* · 10-06-2009, 08:09 PM

Here she is actually in the street

First time since bringing her home that i moved her from the driveway. Needed some tranny fluid after the roll backwards but then she moved forward so i could clean the driveway, seat belts and other stuff off.
Got underneath and did a little more degrease and pressure wash too. Getting her in driving condition real soon.
she starts right up as well!!

I removed the front bumper brackets to clean them up and powdercoat them black. i have 72 outers but want to run a 70 bumper so i think i need those inners.

my67chevytruck · 10-06-2009, 09:07 PM

looking good....

*highperf4x4* · 10-06-2009, 09:32 PM

Cool, looks like you're making good progress!

VA72C10 · 10-06-2009, 10:39 PM

Looking good.

*vegaschevy* · 10-07-2009, 08:31 AM

Quote:

Originally Posted by my67chevytruck

looking good....

Quote:

Originally Posted by highperf4x4

Cool, looks like you're making good progress!

Quote:

Originally Posted by VA72C10

Looking good.

Thank you guys,. Cannot wait to get her actually driving and the front fender and grill fixed.

djw32 · 10-07-2009, 01:03 PM

Wow. This truck is looking good. I'm a lil jealous that your truck looks to sit more level front to back than mine. If you get a chance, will you measure the distance between the ground and the fenders(front and back)?

David

*vegaschevy* · 10-07-2009, 01:19 PM

Quote:

Originally Posted by djw32

Wow. This truck is looking good. I'm a lil jealous that your truck looks to sit more level front to back than mine. If you get a chance, will you measure the distance between the ground and the fenders(front and back)?

David

I cannot remember the measurements off hand but When compared with someone elses measurements It was about 3" low in the back. Like the springs are way sagged.
Ill measure for you later and tell you tire size as well.

*vegaschevy* · 10-07-2009, 09:11 PM

Had time to make it to the DMV today and get a 15 day temp tag to put on the truck so I can get it smogged and registered hopefully tomorrow.

Hopefully I can pass vin inspection with no grill installed. I am going to reinstall the rear bumper and front bumper I had off another truck to hopefully slide by.

Ill keep everyone updated. !!!

I might be able to get this driving tomorrow.

*highperf4x4* · 10-07-2009, 09:18 PM

Sounds cool. Your turn signal lights will be in the bumper right?

*vegaschevy* · 10-07-2009, 09:23 PM

Quote:

Originally Posted by highperf4x4

Sounds cool. Your turn signal lights will be in the bumper right?

I have a 71-72 bumper that is beat and old but if the signals work Im in business.

Ill be eventually installing the earlier bumper with a 67 front end.

10-03-2009, 09:45 PM	#52
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE nah you can tell a low mileage truck because it won't have oil/dirt buildup on the frame/engine/firewall, etc. But the engine may have been rebuilt or replaced at some point. As long as it runs strong is all that matter though eh? Be sure to run some ZDDP in your oil or some Valvoline VR1 to stretch your cam as far as possible.

10-03-2009, 10:03 PM	#53
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Project NOT4SLE cool deal...congrats on getting the fuel issue figured out. Glad it was just the fuel pump... __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-03-2009, 11:38 PM	#54
DuramaxC10 Registered User Join Date: Jul 2009 Location: Mcdonough ,Ga Posts: 59	Re: Project NOT4SLE what happen to project Vegas is that the truck which got stole __________________ 1968 Chevy C10 6/8 drop ( great grandpas truck) under construction 1972 Ford Bronco project 2006 chevy Silverado 2500hd dd 1995 k2500 solid axles 12v cummins crew cab

10-05-2009, 12:32 AM	#57
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Project NOT4SLE They are wallet eaters basically. As I get one thing checked off the list I think of three more I'd like to do "since I already went this far, I might as well......" __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-05-2009, 12:41 AM	#60
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Well, just keep the pics coming

10-05-2009, 12:47 AM	#61
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Project NOT4SLE I'm In!! nice work! __________________ *CHEVY ONLY*

10-05-2009, 01:02 AM	#62
nuke1 Registered User Join Date: Jun 2007 Location: Saskatoon, Saskatchewan,: Posts: 2,901	Re: Project NOT4SLE Hey Deven, truck is coming along great, gonna turn out great, you gonna be around for sema, i will be there that week, as i am going for it! __________________ James 1968 GMC "HAVOC" 1986 GMC "Frank" J.J.R.H. Design & Consulting My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300 A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238 1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361 Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390 Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100 1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587

10-05-2009, 07:21 AM	#64
DuramaxC10 Registered User Join Date: Jul 2009 Location: Mcdonough ,Ga Posts: 59	Re: Project NOT4SLE do you still have project Vegas __________________ 1968 Chevy C10 6/8 drop ( great grandpas truck) under construction 1972 Ford Bronco project 2006 chevy Silverado 2500hd dd 1995 k2500 solid axles 12v cummins crew cab

10-06-2009, 08:09 PM	#66
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: Project NOT4SLE Here she is actually in the street First time since bringing her home that i moved her from the driveway. Needed some tranny fluid after the roll backwards but then she moved forward so i could clean the driveway, seat belts and other stuff off. Got underneath and did a little more degrease and pressure wash too. Getting her in driving condition real soon. she starts right up as well!! I removed the front bumper brackets to clean them up and powdercoat them black. i have 72 outers but want to run a 70 bumper so i think i need those inners.

10-06-2009, 09:07 PM	#67
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project NOT4SLE looking good.... __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

10-06-2009, 09:32 PM	#68
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Cool, looks like you're making good progress!

10-06-2009, 10:39 PM	#69
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Project NOT4SLE Looking good. __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-07-2009, 01:03 PM	#71
djw32 Registered User Join Date: May 2006 Location: So.Cal Posts: 542	Re: Project NOT4SLE Wow. This truck is looking good. I'm a lil jealous that your truck looks to sit more level front to back than mine. If you get a chance, will you measure the distance between the ground and the fenders(front and back)? David

10-07-2009, 09:11 PM	#73
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: Project NOT4SLE Had time to make it to the DMV today and get a 15 day temp tag to put on the truck so I can get it smogged and registered hopefully tomorrow. Hopefully I can pass vin inspection with no grill installed. I am going to reinstall the rear bumper and front bumper I had off another truck to hopefully slide by. Ill keep everyone updated. !!! I might be able to get this driving tomorrow.

10-07-2009, 09:18 PM	#74
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Sounds cool. Your turn signal lights will be in the bumper right?



Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.