![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jul 2009
Location: Miami, FL
Posts: 85
|
checking oil pressure when guage is not working
87 c10 305 TBI. Oil pressure gauge is not working. Its all the way to the right?
Any way to check oil pressure without it? What are the likely causes for the guage not to work? Will I likely need to remove dash to fix it? I went to Autozone to see if I could pull the codes on the Check Engine light but they said their device only works on 1990 and higher. Whats an economical way to get the codes out? Thanks.
__________________
----------------- JC (Cyberpine) My 1987 C10 Short Bed (click on slideshow to see full album) Last edited by cyberpine; 10-20-2009 at 09:00 AM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jul 2007
Location: Ontario Canada
Posts: 1,006
|
Re: checking oil pressure when guage is not working
http://www.troublecodes.net/GM/ that has everything you need
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2007
Location: Franklin Indiana
Posts: 635
|
Re: checking oil pressure when guage is not working
Probably not the gage probably the sending unit. It's on the back of the engine. Under the air cleaners shadow behind the carb on the top back of the block.
__________________
My Truck's not leaking its marking its territory! |
![]() |
![]() |
![]() |
#4 |
One shot, one kill.
Join Date: Dec 2007
Location: Saratoga Springs NY
Posts: 859
|
Re: checking oil pressure when guage is not working
Sending unit for the gage could also be down by the oil filter. To test the gage, locate the sender, ground the wire that goes to it and look at the gage, then unground the wire and look at the gage. One way will be high pressure and the other way low pressure. If the gage reacts like that, replace the sender, if not, check the wire, then replace the gage. Make sure the key is on when you check it.
__________________
1984 K20 350M engine with 465,000 miles. Well, it's finally done!! Almost 2 years of work, but it was really worth the effort. Little stuff left to do is mount winch, wet sand & buff out and build belly pan\running boards. Body work takes lots and LOTS of beer!!!! God, Guts and Guns made America and God, Guts and Guns will preserve it! The worst thing you could do is get into my sights, but that don't matter, you'll never know it, cause you'll never hear the shot ![]() |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2008
Location: la
Posts: 345
|
Re: checking oil pressure when guage is not working
The second sender that you are talking about MCclure is actually a pressure switch that controls choke settings...not the actual gauge. You are correct about testing the sender with the wire.
edit...saw that it is an 87 so maybe the sender is down by the filter but I still doubt it. |
![]() |
![]() |
![]() |
#6 |
One shot, one kill.
Join Date: Dec 2007
Location: Saratoga Springs NY
Posts: 859
|
Re: checking oil pressure when guage is not working
83, Mine's an 84 & the sender is down by the filter. I have no choke heater. The choke heater oil pressure switch will have 2 heavy (10 or 12 gage??) wires on it while the gage sender wire (green??) should be like a 14 gage. jim
__________________
1984 K20 350M engine with 465,000 miles. Well, it's finally done!! Almost 2 years of work, but it was really worth the effort. Little stuff left to do is mount winch, wet sand & buff out and build belly pan\running boards. Body work takes lots and LOTS of beer!!!! God, Guts and Guns made America and God, Guts and Guns will preserve it! The worst thing you could do is get into my sights, but that don't matter, you'll never know it, cause you'll never hear the shot ![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|