|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-25-2002, 08:31 PM
|
#1 |
|
Registered User
Join Date: Sep 2000
Location: Texas
Posts: 189
|
Know a good way to remove rivets at the junkyard?
I'm going to grab a swaybar at the junkyard this weekend and I want to get the frame brackets as well. They don't pull parts for you at this yard, and I don't know if I can come up with a battery powered drill by this weekend to drill them out. So, any suggestions on how to remove these rivets? I don't think a chisel will work, but maybe my chisels aren't good enough.
|
|
|
|
03-25-2002, 08:44 PM
|
#2 |
|
Registered User
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
|
sharpen 2 or3 chisels,& take a BFH with you!
__________________
http://community.webshots.com/user/hotrodhorn |
|
|
|
|
03-25-2002, 08:56 PM
|
#3 |
|
Senior Member
 
Join Date: Mar 2000
Location: Saskatoon,SK,Canada
Posts: 2,476
|
Take a bmf (18 volt) of a cordless drill and drill out the middles of the rivet heads then use the bmf hammer and chisels. Still an ugly job.
__________________
Saskatoon, Saskatchewan Canada |
|
|
|
|
03-25-2002, 09:34 PM
|
#4 |
|
Senior Member
Join Date: Jun 2000
Location: georgia
Posts: 292
|
The easiest way is to buy new ones. They are cheap compared to the work to get the old ones off and they could be bent to boot! Here's the GM part # 6271375. The last ones I bought were $6.50 each whole sale.
|
|
|
|
|
03-25-2002, 09:37 PM
|
#5 |
|
Registered User
Join Date: Mar 2002
Location: Houston, Pennsylvania
Posts: 231
|
Everyone told me to drill, two broken bits and 25min later (with electric) I had 4 rivits out. 4min with a big hammer and a sharp chisel and a punch and some HARD HITTING the other 4 were out! I will NEVER drill again!!
__________________
'96 GMC Suburban 6.5t '99 F**d Windstar '07 SON '09 DAUGHTER XOXOXO Wife |
|
|
|
|
03-25-2002, 09:38 PM
|
#6 |
|
Registered User
Join Date: Sep 2000
Location: Texas
Posts: 189
|
Thanks for the suggestions everyone. I like the buy new ones idea. I think I'll do that.
|
|
|
|
|
03-25-2002, 09:56 PM
|
#7 |
|
Truck Farmer
Join Date: Nov 2001
Location: Lake Havasu City, Arizona
Posts: 1,192
|
If you take a hacksaw and cross cut it to the frame you can use a chisel and pop the head right off. Then a punch to drive them out.
__________________
Arizona rust free sheetmetal |
|
|
|
|
03-25-2002, 10:09 PM
|
#8 |
|
Senior Member
Join Date: Mar 2000
Location: Saskatoon,SK,Canada
Posts: 2,476
|
I like that hack saw idea. I'll have to try it next time.
__________________
Saskatoon, Saskatchewan Canada |
|
|
|
|
03-26-2002, 04:57 AM
|
#9 |
|
Registered User
Join Date: Jun 2000
Location: Springvale,Maine
Posts: 201
|
cordless sawzall,that'll do it
__________________
Springvale,Maine 71 3/4 GMC lwb |
|
|
|
|
03-26-2002, 01:01 PM
|
#10 |
|
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
i nice new sharp chisel will do it, hope you are getting a large 3/4 ton or 1 ton bar!
good luck ------------------ -71/C-10(thx teeitup and crews!)350 4+4/CH465(thx 71Chev, GMCPaul, and CPNE)longfleet bed(thnx meathead95)!still building it- -'84 Z28(Z28) 1G1AP87GXEL100000 with H.O. 305/4bbl/190net/hp(L69) 3.73 rear(GT4/YC4) 700R4(MD8-MXO) & other goodies  -79 G20 pass van, 350/th350/10bolt, paint is overrated Randy- Lincoln, IL r68c30@hotmail.com © RSS Enterprises 2000 |
|
|
|
|
03-26-2002, 04:01 PM
|
#11 |
|
Registered User
Join Date: Sep 2000
Location: Texas
Posts: 189
|
Well, thanks for all the suggestions. I ordered two new ones at the Chevy dealer today. About $10 apiece.
[This message has been edited by j-dogg (edited March 26, 2002).] |
|
|
|
|
03-26-2002, 05:26 PM
|
#12 |
|
Registered User
Join Date: Dec 2001
Location: Philadelphia, pa. U.S.A.
Posts: 87
|
hotrodhenryj's suggestion with a hacksaw and chisel work great. I have used it many times before. a big chisel and about a 3 lb. hammer. good luck
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
