coil rear suspension....... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*project 67 sub* · 12-23-2009, 08:24 PM

can bolts be used in place of u-bolts if so what kind? good idea or bad and why?

**kev2809** · 12-23-2009, 09:11 PM

if u take out the u bolt, and use a bolt, what will hold the axle down?

Super73 · 12-23-2009, 09:17 PM

Not with out some fabrication..

**lolife99** · 12-23-2009, 10:50 PM

Don't do it.
I saw a nice truck destroyed years ago, because a guy did the same thing.
(rearend came out from under the truck at 55mph on a corner)
Get the proper u-bolts!

*project 67 sub* · 12-23-2009, 11:55 PM

i have the proper u bolts in it now i was just thinking cause i think they might end up hitting my notch and not allow it to fully lay out.

**kev2809** · 12-24-2009, 12:38 AM

can u cut like an inch off the bottom of the notch or whatevery u need then plate it back up?

*2tons of fun* · 12-24-2009, 01:54 AM

the bolts would still tighten the the pad down which is welded to the rear. if you dont make a lot of hp, hydro jump, or do high speed driving i would say do it.

however, you would be safer to trim more of your framework to make it clear and keep the u bolt.

Tony@AirRideTech · 12-24-2009, 11:12 AM

I dont think I would guess for a 1/2"

12-23-2009, 08:24 PM	#1
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	coil rear suspension....... can bolts be used in place of u-bolts if so what kind? good idea or bad and why?

12-23-2009, 09:11 PM	#2
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: coil rear suspension....... if u take out the u bolt, and use a bolt, what will hold the axle down? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_] Last edited by kev2809; 12-23-2009 at 09:13 PM.

12-23-2009, 09:17 PM	#3
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: coil rear suspension....... Not with out some fabrication.. __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

12-23-2009, 10:50 PM	#4
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,700	Re: coil rear suspension....... Don't do it. I saw a nice truck destroyed years ago, because a guy did the same thing. (rearend came out from under the truck at 55mph on a corner) Get the proper u-bolts!

12-23-2009, 11:55 PM	#5
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: coil rear suspension....... i have the proper u bolts in it now i was just thinking cause i think they might end up hitting my notch and not allow it to fully lay out.

12-24-2009, 12:38 AM	#6
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: coil rear suspension....... can u cut like an inch off the bottom of the notch or whatevery u need then plate it back up? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

12-24-2009, 01:54 AM	#7
2tons of fun Account Suspended Join Date: Jan 2009 Location: galt ca, Posts: 749	Re: coil rear suspension....... the bolts would still tighten the the pad down which is welded to the rear. if you dont make a lot of hp, hydro jump, or do high speed driving i would say do it. however, you would be safer to trim more of your framework to make it clear and keep the u bolt.

12-24-2009, 11:12 AM	#8
Tony@AirRideTech Junior Member Join Date: Feb 2005 Location: Huntingburg IN Posts: 620	Re: coil rear suspension....... I dont think I would guess for a 1/2"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.