What did you do to your truck today? - Page 43 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ol Curt · 03-18-2010, 08:14 PM

I've been sanding and sanding and sanding on my hood to get the high build primer where I want it. Damn, these hoods are big and with a lot of nooks.

hb32 · 03-18-2010, 11:05 PM

Quote:

Originally Posted by DWright

i have an offy single quad intake. pm me if youre interested.

Check your pm

Vernski · 03-19-2010, 02:45 AM

Quote:

Originally Posted by hb32

No it is a stock 230. Next I am in the market for a Holley 390 cfm carb and a Offenhauser single quad manifold to fix the Rochester stumble.

HB32 check out this web site about the Clifford hot water heated manifold...Vernski

http://prostores1.carrierzone.com/se...119/Categories

**DPowers** · 03-19-2010, 09:25 AM

Quote:

Originally Posted by ol Curt

I've been sanding and sanding and sanding on my hood to get the high build primer where I want it. Damn, these hoods are big and with a lot of nooks.

Man I know what you are talking about.....

daxloves · 03-19-2010, 08:15 PM

Rebuilt the starter today. Brushes were ground down to nubs

Went to get gas and it wouldnt start back up. thought the battery was toast but a diff battery showed otherwise.

Napa couldnt even find anything for a starter on a 305 v6. All they could find was stuff for a 305 v8. Finally a mechanic from the back came out and grabbed some brushed out of a box and said "Here's what ya need" No computer and parts book needed. If it wasnt for him the ladies at the counter woulda been tryin to sell me a whole starter for $90.00 that MIGHT be the rite one! The brushes only cost me $3.65

sshockr · 03-19-2010, 09:33 PM

[vent] Nothing cause mother nature is a tease. It's 60 and sunny at 2 this afternoon and by the time I get home at 5 it's 40 and breezy. Now it's sleeting sideways with predicted snowfalls of 2 inches over night. Supposed to be back to 60 when I go back to work on Monday. [vent off]

- Brian

sams60gmc · 03-19-2010, 10:35 PM

Put some air in my bags then dropped her to the ground. Its sitting on the lower control arms now. Can't wait til its Z'd

sams60gmc · 03-19-2010, 10:39 PM

Quote:

Originally Posted by shortbed70

I just did the same thing with my lowers for alot less then tubular ones and I did it myself.

Looks great! The tube was kind of hard to get in there. I should have went square aswell.

**Bugeyev8** · 03-21-2010, 04:39 AM

I got the rear axle seals changed in my 62 and the rear brakes and cylinders and finished up my tail gate latches, look !! No Chains !!

Slow Build · 03-21-2010, 02:42 PM

Quote:

Originally Posted by Bugeyev8

finished up my tail gate latches, look !! No Chains !!

What did you use for your donor tailgate? I'm guessing 88-98 C1500 but want to be sure. I've been wanting to do the same thing. Looking good.

HOGDADDY · 03-21-2010, 03:28 PM

I got the wiring harness out of the new (used) cab and put the new firewall pad in (what a pia) and loosely installed steering column and ready to put my harness in the new cab.

I was gonna try and use the new harness but it is different than mine and has other options I don't need plus I onlt got the inside part not the matching exterior harness.

I don't want any surprises later. I know my original harness is good so gonna use it.

derider · 03-21-2010, 03:51 PM

Nice work on the tail gate!

sams60gmc · 03-21-2010, 04:00 PM

oops... video below.

sams60gmc · 03-21-2010, 04:01 PM

YouTube- 1960 GMC truck bagged and backhalfed

protrash64 · 03-21-2010, 04:14 PM

Disturbed

.........lookin' good Sam!!!!!!!!

sams60gmc · 03-21-2010, 05:05 PM

Quote:

Originally Posted by protrash64

Disturbed

.........lookin' good Sam!!!!!!!!

thanks bud

**Bugeyev8** · 03-21-2010, 08:10 PM

Quote:

Originally Posted by Slow Build

What did you use for your donor tailgate? I'm guessing 88-98 C1500 but want to be sure. I've been wanting to do the same thing. Looking good.

the latches/cables are 1990 chevy S10. everything else I made

**Bugeyev8** · 03-21-2010, 08:11 PM

Quote:

Originally Posted by derider

Nice work on the tail gate!

Thanks !!

shortbed70 · 03-21-2010, 09:03 PM

Rear bags in and working.

[IMG]http://i52.photobucket.com/albums/g38/smallsc...

creep · 03-21-2010, 09:14 PM

Got some notches in.

64c20crewcab · 03-22-2010, 12:27 AM

Got some base color (POR-15 Silver) on the new motor... Not much in the grand scheme of things but its progress...

jonathan-m · 03-22-2010, 12:31 AM

Quote:

Originally Posted by 64c20crewcab

Got some base color (POR-15 Silver) on the new motor... Not much in the grand scheme of things but its progress...

Hey, progress is progress. I sat on my ass all day and watched it rain

I was hoping to get out and finish up painting my bed, but mother nature said no. This weeks project: find some new tires and rims (easier said than done), and get the damn thing painted.

60apache · 03-22-2010, 08:10 PM

bought a cam picked up block and pistons from machine shop, bought some heads, finished front end, got wheels and tires in.

Bazooka · 03-22-2010, 08:46 PM

Test fitted the gauge panel

jkb · 03-23-2010, 05:36 PM

Finished up the weekend project clean up! Finally dove into betty jean and removed the front clip and the 6 cyl and 3 spd trans. Maybe start my build page this weekend.

03-18-2010, 08:14 PM	#1051
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: What did you do to your truck today? I've been sanding and sanding and sanding on my hood to get the high build primer where I want it. Damn, these hoods are big and with a lot of nooks. __________________ 1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down!

03-19-2010, 08:15 PM	#1055
daxloves Registered User Join Date: Mar 2010 Location: Kettle Falls WA Posts: 48	Re: What did you do to your truck today? Rebuilt the starter today. Brushes were ground down to nubs Went to get gas and it wouldnt start back up. thought the battery was toast but a diff battery showed otherwise. Napa couldnt even find anything for a starter on a 305 v6. All they could find was stuff for a 305 v8. Finally a mechanic from the back came out and grabbed some brushed out of a box and said "Here's what ya need" No computer and parts book needed. If it wasnt for him the ladies at the counter woulda been tryin to sell me a whole starter for $90.00 that MIGHT be the rite one! The brushes only cost me $3.65

03-19-2010, 09:33 PM	#1056
sshockr Registered User Join Date: Oct 2009 Location: Wichita, KS Posts: 91	Re: What did you do to your truck today? [vent] Nothing cause mother nature is a tease. It's 60 and sunny at 2 this afternoon and by the time I get home at 5 it's 40 and breezy. Now it's sleeting sideways with predicted snowfalls of 2 inches over night. Supposed to be back to 60 when I go back to work on Monday. [vent off] - Brian __________________ 1963 Long Bed C10 - LT1/4L60E Swap in Progress. Blew up the straight six and happened to have the engine trans combo on hand already. 1995 Impala SS - LT1/T56 Combo. This is my 1st priority project.

03-19-2010, 10:35 PM	#1057
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? Put some air in my bags then dropped her to the ground. Its sitting on the lower control arms now. Can't wait til its Z'd Attached Images __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

03-21-2010, 04:39 AM	#1059
Bugeyev8 Senior Member Join Date: Aug 2009 Location: San Leandro, Ca 94577 Posts: 854	Re: What did you do to your truck today? I got the rear axle seals changed in my 62 and the rear brakes and cylinders and finished up my tail gate latches, look !! No Chains !! Attached Images

03-21-2010, 03:28 PM	#1061
HOGDADDY Registered User Join Date: Jul 2006 Location: Alabama Posts: 661	Re: What did you do to your truck today? I got the wiring harness out of the new (used) cab and put the new firewall pad in (what a pia) and loosely installed steering column and ready to put my harness in the new cab. I was gonna try and use the new harness but it is different than mine and has other options I don't need plus I onlt got the inside part not the matching exterior harness. I don't want any surprises later. I know my original harness is good so gonna use it. Last edited by HOGDADDY; 03-21-2010 at 03:32 PM.

03-21-2010, 03:51 PM	#1062
derider Registered User Join Date: Feb 2009 Location: Deforest, WI Posts: 90	Re: What did you do to your truck today? Nice work on the tail gate!

03-21-2010, 04:00 PM	#1063
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? oops... video below. __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718 Last edited by sams60gmc; 03-21-2010 at 04:01 PM.

03-21-2010, 04:14 PM	#1065
protrash64 Resistance is Futile Join Date: Dec 2006 Location: Mesa,Arizona Posts: 3,520	Re: What did you do to your truck today? Disturbed.........lookin' good Sam!!!!!!!! __________________ 64 CHEVY PICK-UP > http://67-72chevytrucks.com/vboard/s...otrash+re-hash 64 CARRYALL >http://67-72chevytrucks.com/vboard/s...=1964+suburban 66 LB >http://67-72chevytrucks.com/vboard/s...d.php?t=427852 STRENGTH/DETERMINATION/MERCILESS/FOREVER .......posted via stationary device

03-21-2010, 09:14 PM	#1070
creep Registered Loser Join Date: Jun 2009 Location: Elyria, OH Posts: 1,523	Re: What did you do to your truck today? Got some notches in. __________________ ((..)) ((0)) '63 GMC lwb, 383, th350, lays frame, genuine patina. The Build Thread - http://67-72chevytrucks.com/vboard/s...d.php?t=374267 '88 Astro cargo bagged, shaved, phantom grille. SOLD '50 Chevy 2 door sedan awaiting attention. 2014 Silverado Ext cab, 5.3, daily driver.

03-22-2010, 12:27 AM	#1071
64c20crewcab Registered User Join Date: Jun 2008 Location: North SD County Posts: 631	Re: What did you do to your truck today? Got some base color (POR-15 Silver) on the new motor... Not much in the grand scheme of things but its progress... __________________ ..............................._________ ......___________//___[[___{\ _____ ...../__(_(O)_)___/____/____/_(O)_/ 1964 C20 Long Stepside 3 Door Crew Cab - Armbruster-Stageway Conversion Y2K INDN Chief "ONE OF A KIND, NOT ONE OF THE CROWD" Aug 2010 - Front end frame cleanup & engine swap done!!! June 2011 - Rear end bagged Sept 2011 - Rebuild motor top end Sept 2012 - Parked and slowly working on it. Aug 2013 - Front end bagged - finally! Aug 2014 - Stepside swap conversion done. Finally ready to start bodywork! Have a few KEWL ideas... Here is my build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=335427

03-22-2010, 08:10 PM	#1073
60apache Registered User Join Date: Mar 2010 Location: brandon, ms Posts: 385	Re: What did you do to your truck today? bought a cam picked up block and pistons from machine shop, bought some heads, finished front end, got wheels and tires in. Attached Images

03-22-2010, 08:46 PM	#1074
Bazooka Keepin it old school Join Date: Jul 2008 Location: Ca Posts: 672	Re: What did you do to your truck today? Test fitted the gauge panel

03-23-2010, 05:36 PM	#1075
jkb Registered User Join Date: Apr 2009 Location: Dearborn Hgts, MI Posts: 47	Re: What did you do to your truck today? Finished up the weekend project clean up! Finally dove into betty jean and removed the front clip and the 6 cyl and 3 spd trans. Maybe start my build page this weekend. Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.