** YOUNG FRANKENSTEIN ** The truck Chevrolet should have built. - Page 40 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VA72C10 · 03-22-2011, 06:37 PM

Here you go....

**67cheby** · 03-22-2011, 06:42 PM

wow...very nice guideline !!

VA72C10 · 03-22-2011, 06:43 PM

Quote:

Originally Posted by 67cheby

wow...very nice guideline !!

It only took me 3 tries to put the right numbers on

67HEAVEN · 03-22-2011, 06:53 PM

Drew,

Having done a complete rebuild of my '67 Corvette, I have an immense appreciation for your creativity, craftsmanship and amazing speed.

That truck will be a real beauty and a wonderful "family" vehicle. Well done hardly seems to be adequate praise.

thor · 03-22-2011, 07:45 PM

Quote:

Originally Posted by VA72C10

Here you go....

Nice! And, thank you! Great detail!

classicchev · 03-22-2011, 07:55 PM

Quote:

Originally Posted by drewskiren

It's really all just trick photography.

I think it may be the patented cross draft spray booth

I have the same one, and its perfect for what I do, and no complaints from any neighbours yet, knock on wood.

Looking good.

Darren

FRENCHBLUE72 · 03-22-2011, 07:59 PM

How far is ar from tn hahhahahha Paint looks killer and reminds me of kevins low buk build..

jugernot · 03-22-2011, 08:14 PM

I have seen this thread many times but never opened it till now. That is quite a build and will be a sweet ride. Nice work

drewskiren · 03-22-2011, 08:41 PM

DANG, I'm gone to the soccer fields for 2 hours and there are 10 posts!

Thanks so much for the diagram!!! Next time though, could you color code each screw hole for me??????

I just checked another door and my bed front and both are 13.5 inches from the center of the upper trim hole down to the body line (a 13.5 inch white stripe). Is this correct too? I think this works out the same also on the rear of the fender. I don't want to paint it twice!!!

drewskiren · 03-22-2011, 10:19 PM

I got the hood done tonight, and all was going well until I had a couple of critters decide to join in the fun. I got one out with the tweezers, but the other was just a little guy. He got painted over on the 4th coat, but that one I laid on a little too heavy and created a signature on the front edge. Friday I will wet sand the run and my little friend's paw prints and shoot one last heavy - but run free- coat and call it done. While I am wet sanding with 400 grit I will use my block and knock down the orange peel so the last coat will turn out really flat. My goal all over will be like the 4th pic where you can almost read the writing on the fluorescent bulbs. If I can't get there by painting I can always buff it there.

Flint70step · 03-22-2011, 10:30 PM

Wow man, you got that last coat pretty flat.You can almost read the lettering on the light bulb.After seeing this build,it has severely diminished my fear of doing my own paint.Not only would it save me truck loads of cash, but the satisfaction of doing it yourself and doing it well has a lot more value than paying some one to do it.I think you deserve truck of the year even before its done.Nice work Drew.Yall be good

VA72C10 · 03-22-2011, 10:33 PM

I have 16" between center of the holes on the rear of my cab. And same between the paint on my fenders.

Not sure of the paint line as mine is all white

Maybe someone else will know where the break should be (center of holes or top of trim)

drewskiren · 03-22-2011, 10:37 PM

Quote:

Originally Posted by Flint70step

Wow man, you got that last coat pretty flat.You can almost read the lettering on the light bulb.After seeing this build,it has severely diminished my fear of doing my own paint.Not only would it save me truck loads of cash, but the satisfaction of doing it yourself and doing it well has a lot more value than paying some one to do it.I think you deserve truck of the year even before its done.Nice work Drew.Yall be good

THAT'S what I'm talking about!!!! I'm telling you guys, it's not that impossible. It is certainly worth trying on a spare hood and seeing what you can do. Buy a how to video, talk to the local paint supply house, ask me, whatever!

Truck of the month would be awesome (not so sure about year), but the category would have to be "in process".

drewskiren · 03-22-2011, 10:39 PM

Quote:

Originally Posted by VA72C10

I have 16" between center of the holes on the rear of my cab. And same between the paint on my fenders.

Not sure of the paint line as mine is all white

Maybe someone else will know where the break should be (center of holes or top of trim)

I got 13.5 to the body line, I don't have any parts with trim holes top and bottom to measure between the holes.

Rumble · 03-23-2011, 12:49 PM

I have wanted to do one of these for years, not enough knowledge or time, great attention to detail
i ended up with this as my project, still workin on it
it started out as a 1 ton long bed dually, i should be gettin from paint shop today ( stayed with factory white)

mrchrishill · 03-23-2011, 01:06 PM

Lookin' good Drewski. What are you going to do for a dash now that you crammed that full AC into it?

jbclassix · 03-23-2011, 01:43 PM

Quote:

Originally Posted by Rumble

I have wanted to do one of these for years, not enough knowledge or time, great attention to detail
i ended up with this as my project, still workin on it
it started out as a 1 ton long bed dually, i should be gettin from paint shop today ( stayed with factory white)

Quote:

Originally Posted by mrchrishill

Lookin' good Drewski. What are you going to do for a dash now that you crammed that full AC into it?

Drew always attracts new members!

drewskiren · 03-23-2011, 04:38 PM

Quote:

Originally Posted by jbclassix

Drew always attracts new members!

Can I get a referral discount on my membership???

drewskiren · 03-24-2011, 12:33 AM

Quote:

Originally Posted by mrchrishill

Lookin' good Drewski. What are you going to do for a dash now that you crammed that full AC into it?

Funny you should ask, mrchrishill, I have a few ideas up my sleeve but I haven't fully worked them out yet.

mcbassin · 03-24-2011, 07:40 AM

Drew, did you already say in here what kind of paint you're shooting? Is that single stage acrylic enamel, urethane enamel, or polyurethane? It looks great, btw, I know first hand about critters in the paint (still have one or two I need to buff out of my son's paint). I have had another fun problem with sweat building up on me and dripping on the paint. If you wear coveralls hood and resporator it gets HOT. keep the pics rolling!

silverboy02 · 03-24-2011, 09:32 AM

Post #855 shows he is using Nason acrylic enamel

JasonBird · 03-24-2011, 09:37 AM

Quote:

Originally Posted by drewskiren

Can I get a referral discount on my membership???

i doubt it, but i'll let ya paint my truck for free!

67Cheby probably take you up on that offer, in fact we'll pay next years member ship fee for you for painting our rigs!

JT

**67cheby** · 03-24-2011, 09:40 AM

thats for sure

drewskiren · 03-24-2011, 10:16 AM

Quote:

Originally Posted by mcbassin

Drew, did you already say in here what kind of paint you're shooting? Is that single stage acrylic enamel, urethane enamel, or polyurethane? It looks great, btw, I know first hand about critters in the paint (still have one or two I need to buff out of my son's paint). I have had another fun problem with sweat building up on me and dripping on the paint. If you wear coveralls hood and resporator it gets HOT. keep the pics rolling!

Quote:

Originally Posted by silverboy02

Post #855 shows he is using Nason acrylic enamel

Yes, just the least expensive acrylic enamel single stage. I usually shoot base/clear, but it is so large, I didn't want to spend the time or money.

drewskiren · 03-24-2011, 10:27 AM

WOW, 1000 posts and 66,000 views !!! Thanks everyone, couldn't have done it without you.

03-22-2011, 06:37 PM	#976
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Here you go.... Attached Images __________________ Looking for a 67-72 swb or blazer project in or around VA. Last edited by VA72C10; 03-22-2011 at 06:42 PM.

03-22-2011, 06:42 PM	#977
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. wow...very nice guideline !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-22-2011, 06:53 PM	#979
67HEAVEN www.67HEAVEN.com Join Date: Oct 2007 Location: SouthCentral Ontario Posts: 625	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Drew, Having done a complete rebuild of my '67 Corvette, I have an immense appreciation for your creativity, craftsmanship and amazing speed. That truck will be a real beauty and a wonderful "family" vehicle. Well done hardly seems to be adequate praise. __________________ www.67HEAVEN.com 2004 Z71 Tahoe 4x4 5.3L (factory white monochrome theme) 1989 Silverado K1500 4x4 5.7L sportside (white monochrome theme) 1967 Belair 2-door-post (project) 1967 Corvette 427/435 coupe (now 502/502 red road warrior)

03-22-2011, 07:59 PM	#982
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. How far is ar from tn hahhahahha Paint looks killer and reminds me of kevins low buk build.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-22-2011, 08:14 PM	#983
jugernot Life, Be In It..... Join Date: Oct 2003 Location: Novato, California Posts: 1,498	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I have seen this thread many times but never opened it till now. That is quite a build and will be a sweet ride. Nice work __________________ Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082

03-22-2011, 08:41 PM	#984
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. DANG, I'm gone to the soccer fields for 2 hours and there are 10 posts! Thanks so much for the diagram!!! Next time though, could you color code each screw hole for me?????? I just checked another door and my bed front and both are 13.5 inches from the center of the upper trim hole down to the body line (a 13.5 inch white stripe). Is this correct too? I think this works out the same also on the rear of the fender. I don't want to paint it twice!!! __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife! Last edited by drewskiren; 03-22-2011 at 09:56 PM.

03-22-2011, 10:19 PM	#985
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I got the hood done tonight, and all was going well until I had a couple of critters decide to join in the fun. I got one out with the tweezers, but the other was just a little guy. He got painted over on the 4th coat, but that one I laid on a little too heavy and created a signature on the front edge. Friday I will wet sand the run and my little friend's paw prints and shoot one last heavy - but run free- coat and call it done. While I am wet sanding with 400 grit I will use my block and knock down the orange peel so the last coat will turn out really flat. My goal all over will be like the 4th pic where you can almost read the writing on the fluorescent bulbs. If I can't get there by painting I can always buff it there. Attached Images __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife! Last edited by drewskiren; 03-24-2011 at 01:12 PM.

03-22-2011, 10:30 PM	#986
Flint70step Registered User Join Date: Jan 2011 Location: Lake Travis,Texas Posts: 586	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Wow man, you got that last coat pretty flat.You can almost read the lettering on the light bulb.After seeing this build,it has severely diminished my fear of doing my own paint.Not only would it save me truck loads of cash, but the satisfaction of doing it yourself and doing it well has a lot more value than paying some one to do it.I think you deserve truck of the year even before its done.Nice work Drew.Yall be good

03-22-2011, 10:33 PM	#987
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I have 16" between center of the holes on the rear of my cab. And same between the paint on my fenders. Not sure of the paint line as mine is all white Maybe someone else will know where the break should be (center of holes or top of trim) __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-23-2011, 12:49 PM	#990
Rumble Registered User Join Date: Oct 2010 Location: temecula, ca Posts: 29	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I have wanted to do one of these for years, not enough knowledge or time, great attention to detail i ended up with this as my project, still workin on it it started out as a 1 ton long bed dually, i should be gettin from paint shop today ( stayed with factory white) Attached Images Last edited by Rumble; 03-23-2011 at 12:50 PM.

03-23-2011, 01:06 PM	#991
mrchrishill Registered User Join Date: Mar 2011 Location: Memphis, TN Posts: 10	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Lookin' good Drewski. What are you going to do for a dash now that you crammed that full AC into it?

03-24-2011, 07:40 AM	#995
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Drew, did you already say in here what kind of paint you're shooting? Is that single stage acrylic enamel, urethane enamel, or polyurethane? It looks great, btw, I know first hand about critters in the paint (still have one or two I need to buff out of my son's paint). I have had another fun problem with sweat building up on me and dripping on the paint. If you wear coveralls hood and resporator it gets HOT. keep the pics rolling! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

03-24-2011, 09:32 AM	#996
silverboy02 Registered User Join Date: May 2008 Location: Grenada, MS Posts: 127	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Post #855 shows he is using Nason acrylic enamel Last edited by silverboy02; 03-24-2011 at 09:33 AM.

03-24-2011, 09:40 AM	#998
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. thats for sure __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-24-2011, 10:27 AM	#1000
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. WOW, 1000 posts and 66,000 views !!! Thanks everyone, couldn't have done it without you. __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife!



Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.