Well..new tires and alignment, STILL veers violently!! HELP! - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

outlaw · 08-11-2003, 02:02 AM

have someone apply the brakes loosen the bleeder screw and see how much pressure the brake fluid has and do the same to the other side if they are differant then you know where your problem lies

pa_snowman · 08-18-2003, 11:39 PM

all this about the calipers and hoses, did anyone think that the propotioning might be bad or stuck? i have a 79 3/4 ton van that had one go bad. when you applied the brakes it would turn right then go straight, when you released the brakes it would try to go left then straight. i changed both rotors, calipers, wheel bearings and still had the problem until i changed the valve.
i know they never go bad, right- but MINE DID!

pa_snowman · 12-24-2005, 05:01 PM

clean the caliper mounts every time you remove the calipers. they slide on the resting points and if their is rust or dirt there it will cause the caliper to hangup and drag.

dwcsr · 12-24-2005, 06:13 PM

I had the same thing on a 92 GMC 1500 and it was brake line after I changed everything else. The line was colapsed inside and would not let fluid return to the master making the caliper drag. I would change them both and be done with it.

**N2TRUX** · 12-24-2005, 06:27 PM

Digging up bones? This thread was started in 2003.....

**Boog** · 12-24-2005, 10:46 PM

And the original poster either never found his problem or sold the truck or gave up or just didn't want to finally post what the problem was?

MOTHERTRUCKERS · 12-25-2005, 08:22 AM

2003? surely it is fixed by now.

SCOTI · 12-26-2005, 12:39 AM

He's not around anymore. I remember reading about his welcome wearing thin as well.

XXL · 12-26-2005, 01:30 PM

Quote:

Originally Posted by pa_snowman

all this about the calipers and hoses, did anyone think that the propotioning might be bad or stuck? i have a 79 3/4 ton van that had one go bad. when you applied the brakes it would turn right then go straight, when you released the brakes it would try to go left then straight. i changed both rotors, calipers, wheel bearings and still had the problem until i changed the valve.
i know they never go bad, right- but MINE DID!

Prop valve works from front to rear. There's a single front line that comes out, and then splits afterward to feed the 2 front corners. Not likely that a prop valve could affect a single side.

And N2TRUX... of course, it's Xmas. We're bored.

**N2TRUX** · 12-26-2005, 04:22 PM

Quote:

Originally Posted by MOTHERTRUCKERS

2003? surely it is fixed by now.

Appearently you don't know Tim very well. My guess is he is still considering his options on what to do here.

phantom dually · 12-26-2005, 05:14 PM

I saw Tim over at FSC. A character for sure!!

FRENCHBLUE72 · 12-29-2005, 05:32 PM

He had some issues with agirl friend or something have not seen him for quite some time...

*screamin_c102* · 12-30-2005, 08:36 PM

Maybe he "Veered Violently" into the path of an on-coming 18 wheeler, or off a cliff, and was never heard from again......

Brakes are not something you half-ass or do on the cheap. I'd rather be able to stop than go any day of the week.

mister honey · 12-31-2005, 11:31 AM

I miss TIMSPEED!

Mike

*DroppedZ84* · 01-08-2006, 01:37 AM

Quote:

Originally Posted by screamin_c10

Maybe he "Veered Violently" into the path of an on-coming 18 wheeler, or off a cliff, and was never heard from again......

I heard he was "offed"

08-18-2003, 11:39 PM	#27
pa_snowman Registered User Join Date: Aug 2003 Location: Meyersdale, PA Posts: 144	all this about the calipers and hoses, did anyone think that the propotioning might be bad or stuck? i have a 79 3/4 ton van that had one go bad. when you applied the brakes it would turn right then go straight, when you released the brakes it would try to go left then straight. i changed both rotors, calipers, wheel bearings and still had the problem until i changed the valve. i know they never go bad, right- but MINE DID! __________________ jim gallagher

12-24-2005, 05:01 PM	#28
pa_snowman Registered User Join Date: Aug 2003 Location: Meyersdale, PA Posts: 144	Re: Well..new tires and alignment, STILL veers violently!! HELP! clean the caliper mounts every time you remove the calipers. they slide on the resting points and if their is rust or dirt there it will cause the caliper to hangup and drag. __________________ jim gallagher

12-24-2005, 06:13 PM	#29
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,131	Re: Well..new tires and alignment, STILL veers violently!! HELP! I had the same thing on a 92 GMC 1500 and it was brake line after I changed everything else. The line was colapsed inside and would not let fluid return to the master making the caliper drag. I would change them both and be done with it.

12-24-2005, 06:27 PM	#30
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: Well..new tires and alignment, STILL veers violently!! HELP! Digging up bones? This thread was started in 2003..... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

12-24-2005, 10:46 PM	#31
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,514	Re: Well..new tires and alignment, STILL veers violently!! HELP! And the original poster either never found his problem or sold the truck or gave up or just didn't want to finally post what the problem was? __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

08-11-2003, 02:02 AM	#26
outlaw Registered User Join Date: Dec 2002 Location: Leesville, Louisiana Posts: 80	have someone apply the brakes loosen the bleeder screw and see how much pressure the brake fluid has and do the same to the other side if they are differant then you know where your problem lies

12-25-2005, 08:22 AM	#32
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	Re: Well..new tires and alignment, STILL veers violently!! HELP! 2003? surely it is fixed by now. __________________ Rest in Peace Ed. Thanks for all the good times.

12-26-2005, 12:39 AM	#33
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Re: Well..new tires and alignment, STILL veers violently!! HELP! He's not around anymore. I remember reading about his welcome wearing thin as well. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-26-2005 at 12:39 AM.

12-26-2005, 05:14 PM	#36
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Re: Well..new tires and alignment, STILL veers violently!! HELP! I saw Tim over at FSC. A character for sure!! __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

12-29-2005, 05:32 PM	#37
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: Well..new tires and alignment, STILL veers violently!! HELP! He had some issues with agirl friend or something have not seen him for quite some time... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-30-2005, 08:36 PM	#38
screamin_c102 Account Suspended Join Date: Feb 2005 Location: Yoncalla Oregon Posts: 775	Re: Well..new tires and alignment, STILL veers violently!! HELP! Maybe he "Veered Violently" into the path of an on-coming 18 wheeler, or off a cliff, and was never heard from again...... Brakes are not something you half-ass or do on the cheap. I'd rather be able to stop than go any day of the week.

12-31-2005, 11:31 AM	#39
mister honey Registered User Join Date: Feb 2004 Location: eastern blowville heights, ohio Posts: 57	Re: Well..new tires and alignment, STILL veers violently!! HELP! I miss TIMSPEED! Mike

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.