What did you do to your truck today!

[magwakeenercew2jh]

Andy,

Sorry if the info is posted in another place, but did you have to/was your dash cut for this? Very nice.

[Andy4639]

magwakeenercew2jh,
I cut my dash several years ago. Most on here will say not to but it's not a big deal to me since the truck has been modified everywhere else.
If you changed the wheels on your truck then who cares if the dash has been cut. As long as it's done right just like any other mod to it.
I went from this to this.

Before:


After:

[magwakeenercew2jh]

Nice.

[Andy4639]

Thanks. It's great having my music when I want and not messing with CD all the time. I have a old CD changer under the passenger seat. I'm taking it out. May put it in one of my Golf carts.

[Shyguy]

I went to my son's place early this morning to help work on my grandson's '73 Malibu and my '67 swb stepper cab.

We got the master cylinder and rear axle seals replaced in my grandson's Malibu.

While my son was welding in the patches I made and he tacked in last Monday I made some patch metal pieces for the kick panels and the passenger side outer floor. I used pieces of an old hood to make the patch panels today. I used an angle grinder with a cut-off wheel to cut out the patch panels and an angle grinder with a grinding wheel to massage the patch panels so they would fit.

I was smart today, I took my own power tools and a very large face shield with leather gloves.

My son was almost done welding in the panels from last week when he ran out of wire.

We stopped for the day so we could straighten and clean the garage.

[Andy4639]

Originally Posted by Shyguy

I went to my son's place early this morning to help work on my grandson's '73 Malibu and my '67 swb stepper cab.

We got the master cylinder and rear axle seals replaced in my grandson's Malibu.

While my son was welding in the patches I made and he tacked in last Monday I made some patch metal pieces for the kick panels and the passenger side outer floor. I used pieces of an old hood to make the patch panels today. I used an angle grinder with a cut-off wheel to cut out the patch panels and an angle grinder with a grinding wheel to massage the patch panels so they would fit.

I was smart today, I took my own power tools and a very large face shield with leather gloves.

My son was almost done welding in the panels from last week when he ran out of wire.

We stopped for the day so we could straighten and clean the garage.

Thats a cool day. Nothing like the family hanging out together doing what they love doing!
I drove mine to work tonight!

[FRENCHBLUE72]

I opened up parts from board member magwakeener... Thanks Im pretty sure theose pieces will work perfect..

[magwakeenercew2jh]

Originally Posted by FRENCHBLUE72

. Thanks Im pretty sure theose pieces will work perfect..

My pleasure. One of these days I'll swing by to collect that Coca∼Cola.


I spent the last couple of days driving. My car. Most of the time on the road, I was thinking about the next "chore" on the 6/71 Rat.

" Hummmm....PB Blast the rear bleeder nipples, route the window washer hoses through the cowl, "egg out" a couple of holes that made the dash pad peak-up a little, etc., etc." "Then, put the front clip back on....Now that I have the correct rad. core support bolt/spacer/pad kit, that is."

Made the drive seem shorter, for sure.

There was some new (truck) trim at the door when I got home this evening.

[MUDSLT]

Originally Posted by Andy4639

I ordered this kit today from "No Limit" a vendor here!

Do you have any more pictures of this setup?

[stealthy '69]

I spent all day, from 11am to 8:30pm, cleaning my garage and working on my truck. I got the rear 5" springs in, but nothing else. My little 25 gallon air compressor wouldn't power my impact enough to remove the track bar or axle u-bolts. And I spent a "good" 2-2.5 hours removing the mini spool I put in 3 years ago and re-installing the spider gears. No more hard turning and no more . Now she's a peg legger! Which I'm OK with. I'd rather have drive-ability then "posi".

[stealthy '69]

Originally Posted by MUDSLT

Do you have any more pictures of this setup?

Check the link he posted above. There are more pics, and the designer him-self, whom will be able to answer your questions to the fullest. Not that Andy can't.

Originally Posted by Andy4639

Here is the link over in the Suspension area.

http://67-72chevytrucks.com/vboard/s...d.php?t=477839

[ItsRandy]

Painted the cab...red.

[RossRinSD]

Spent all day in the garage. Projects were successfully completed. I replaced the pinion and cover seal on the rearend, finished welding up and painting the rear bumper, replaced the melted dimmer switch and damaged wires, Installed a new headlight harness that uses relays right next to the battery, ran the wires for a set of foglights to be installed with the new front bumper, and yanked out all the rusty nasty old bolts that held the bed to the frame. I installed all new nice and shiny stainless steel ones.

And, the best part is that I still have more parts on the bench, and more stuff to do next week.

I did scrape about 15 lbs of dirt encrusted grease off the bottom of the bed and the rearend, the pinion seal was leaking pretty bad.

[magwakeenercew2jh]

Originally Posted by ItsRandy

Painted the cab...red.

Ohhhhhhhhhhhh! Thank you for that vision tonight!!!

[Andy4639]

Originally Posted by MUDSLT

Do you have any more pictures of this setup?

I have not installed this yet on mine. I just used the picture on the other post to show it. I hope to have it on by next weekend if it gets here next week. The thread that stealthy '69 posted is a better place to ask than here. I did the same thing.

The kit has to make it a better ride than what I have now.

[Bennett68C10]

cleaned up the winshield and door channels and shot some primer on them

[RossRinSD]

Originally Posted by stealthy '69

My little 25 gallon air compressor wouldn't power my impact enough to remove the track bar or axle u-bolts.

You sure its the compressor, and not the impact gun? I've used several of the basic impact guns that they include in the kits. I don't think they make much more than about 100 ft/lbs. Home Depot carries a nice IR impact that makes over 600 ft/lbs. That should be plenty to snap your lug nuts off.

[RossRinSD]

Yay. I got my windshield washer squirter things working. Ehh, they are so often overlooked until you really need them. Just working on getting this K10 to a friendly daily driver status. Don't get me wrong, I drive it more than anything else, its just that there are a few things that irritate me.

[Rob H.]

I picked up a 69 K/10 awhile back to use in converting my 72 to 4x4. When I pulled the bed I found alot of rust on the frame and spring hangers. So being the frugal individual I am, I talked to my neighbor and he had a 71 C/20 with leaf springs down in his junkyard (yes I know there are differances in the C vs. K frames, but I could deal with that). I went over last night and drug it out of the weeds and cut the bed off. Went back this morning and torched the rails into behind the carrier bearing cross member and picked it up with the front end loader and carried it over to my place. We were flooded last year so the frame from the 71 was covered with mud. After knocking it off I found more rust, behind the front spring hanger on the drivers side, basically same place as on my K/10 frame. So I took it back and dropped it off in the junkyard where I got it from. Back to plan A (cutting down a 78 K/10 frame), but anyway here's some pics of the rust.


And what I found on the new frame!

[dukcaln]

took passenger side header off to replace the leakie gasket..... will put back on tomorrow with the new gaskets installed..

[Andy4639]

Drove it 535 miles in 24 hours.

[stealthy '69]

Originally Posted by RossRinSD

You sure its the compressor, and not the impact gun? I've used several of the basic impact guns that they include in the kits. I don't think they make much more than about 100 ft/lbs. Home Depot carries a nice IR impact that makes over 600 ft/lbs. That should be plenty to snap your lug nuts off.

Yea I know it's the compressor not the impact (Craftsman Pro Series). I've used the impact at work and had no problems. My comp. is only 25 gallon, It just won't run the volume of air needed to really power it the way it should be.

[71tahoe]

Originally Posted by stealthy '69

Yea I know it's the compressor not the impact (Craftsman Pro Series). I've used the impact at work and had no problems. My comp. is only 25 gallon, It just won't run the volume of air needed to really power it the way it should be.

So what's the torque on your air gun? Last time I tackled the u-bolt nuts I used a 2' breaker bar and about a 250# deadlift effort. That's 500 lb-ft.

[into69z]

I wanted to restore the painted letters on my tailgate that were covered over 22 years ago when the truck was painted. I bought the vinyl letters on e-bay and began to install them. They give you one extra letter to practice with so I put on "chevr"........and then the "r" didn't look just right so i tried to adjust it.....that's when it pealed the paint off exposing about an inch of the old white letter, d@#$ it...so now I pulled off the other letters-wound up with no new letters and about three areas that pulled the paint off on a otherwise clean dark blue tail gate. sucks!

[RossRinSD]

Originally Posted by stealthy '69

Yea I know it's the compressor not the impact (Craftsman Pro Series). I've used the impact at work and had no problems. My comp. is only 25 gallon, It just won't run the volume of air needed to really power it the way it should be.

My fuggin compresser finally died. Its been having some issues, takes forever to get pressure over 100 PSI. Its a decent Craftsman I purchased almost 15 years ago. I let a buddy borrow it/stored it as his house while I was moving about 2 years ago. When I got it back, the little plastic air filter holder was broken. I didn't worry too much about it at the time...

FFWD to today when the thing won't get up over 60 PSI. I pulled the head, and found where a piece of the plastic air filter holder had gotten in, screwed up the ring on the piston, and then the piston scuffed the hell out of the bore sleeve.

What sucks even more is I saved up for a plasma cutter which will be delivered tomorrow, but with no compressor, I won't get to use it.

Anybody know where I can buy a rebuild kit for a Craftsman compressor? A new sleeve and piston ring should get me by for the next 15 years...

And people wonder why I hate loaning my stuff out...

I did however get my radiator overflow bottle installed. It worked wonderfully, except I didn't fill it enough, the engine warmed up and purged all this air out, and maybe a cup or two of coolant into the resevoir. Once it cooled back down, it sucked the resevoir dry, and probably a bunch of air.