Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
09-11-2003, 08:32 PM | #1 |
GYRO GEARLOOSE
Join Date: Jun 2000
Location: Nevada City, CAEverett, WA
Posts: 361
|
Plastic SB ENGINE MOCKUP'S
Does anyone know where to get those SB engine mockup's like I've seen on some TV shows? I also have seen polystyrene trammy's too. Where do I find them, how much?
__________________
Nevada City, CA Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB. 350 from '68, 200R4 tranny, 3.07 rear ratio, restoring 68 C10 LWB 350 4spd, 4.56 rear dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna 85 Tercel SW, snow runner DISGRACED OUTLAW MEMBER OF THE DRUM BRAKE CLUB |
09-11-2003, 08:42 PM | #2 |
D.U.F. Member
Join Date: Nov 2002
Location: Huron/Brookings, SD
Posts: 288
|
I know what you're talking about. I remember seeing an article on them in an old Car Craft or something. This is all I could come up with. I don't think this is the manufacterer of them, just a vendor. Hope this helps.
http://partsboy.com/chevroletreplicaengines.htm
__________________
MEMBER OF THE DISCS UP FRONT CLUB '72 C-10 LWB Highlander, A/C, tilt TH350 w/ B&M shift kit, 327LJ bored .040", cast flattops, forged crank, L31 Vortecs, 9.25:1 CR, Comp conical valvesprings, Crane Energizer single pattern 216/.454", Professional Products Power Plus Crosswind intake, Edelbrock #1406 600cfm, HEI, dual exhaust, open 3.08 12bolt '68 C-10 4spd (not running) '79 C-10 LWB Mild 350 '80 Caprice Classic, 2-dr '97 GMC K-1500, SWB, Reg. Cab, Z-71, 5.7, Auto |
09-11-2003, 08:49 PM | #3 |
GYRO GEARLOOSE
Join Date: Jun 2000
Location: Nevada City, CAEverett, WA
Posts: 361
|
Just did a search, found P-ayr products, long block is about $350, tranny is $250, too much!
__________________
Nevada City, CA Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB. 350 from '68, 200R4 tranny, 3.07 rear ratio, restoring 68 C10 LWB 350 4spd, 4.56 rear dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna 85 Tercel SW, snow runner DISGRACED OUTLAW MEMBER OF THE DRUM BRAKE CLUB |
09-11-2003, 09:03 PM | #4 |
Account Suspended
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
|
Imagine the look on someones face when you bend over and lift one. They have threaded holes and will accept any bolt-on parts.
|
09-11-2003, 09:38 PM | #5 |
Registered User
Join Date: Oct 2000
Location: From Chicago, Live in Phoenix, AZ
Posts: 6,802
|
__________________
Just sitting here contemplating contemplation. |
09-11-2003, 10:19 PM | #6 |
Account Suspended
Join Date: Jul 2003
Posts: 1,284
|
the one on ebay is a good deal we paid alot more for ours
|
09-11-2003, 11:20 PM | #7 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
speedway motors has them
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
09-12-2003, 10:19 AM | #8 |
Registered User
Join Date: Jul 2002
Location: St. James, MO
Posts: 1,238
|
You could buy a junk engine for a heckuva lot less Heck, I sold a decent, 3,000-miles-on-the-rebuild 307 for a lot less!
__________________
'69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt. |
09-12-2003, 12:04 PM | #9 |
Registered User
Join Date: Sep 2003
Location: Chino Valley AZ
Posts: 25
|
I had an old block that I had to leave behind when we moved cross country, left it with a freind. I stripped everything out of it, then started drillin holes. I just left the drill there and the cuttin oil. then whenever the mood struck I would drill out a new hole. After a couple of years it was lookin very swiss cheesy. Dont know if it lightened it up all that much but it looked cool and was fun. I also had junk heads (heavy) and a stripped out turbo 350. Total cost was a twelve pack of beer! Wish I had them now. They were handy for mock-up.
__________________
68 C20 lnb |
09-12-2003, 01:53 PM | #10 |
Formerly yellow72custom
Join Date: May 2001
Location: Austin, TX
Posts: 7,531
|
I saw one of those at Autozone once.....it was sitting on a little stand that looked way to puny to hold a SBC...i thought it was real until i bumped into it and it easily moved, lol. They fooled me.....
__________________
'72 Chevy C10 Mild 350/TH350/3.07. Ochre/White. Old high school ride. '70 GMC C2500 '62 327 4bbl/SM465/4.56-geared Dana 60. White/White. Project or parts truck. '97 Saturn SL DD. 1.9/5-speed. 40+ highway mpg |
09-12-2003, 02:01 PM | #11 |
Guest
Posts: n/a
|
I saw one the other day and I thought it said it was 49.99
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|