power steering bracket - The 1947 - Present Chevrolet & GMC Truck Message Board Network

76bonanza · 11-24-2003, 08:48 PM

Any one know where I can get a power steering upper mounting bracket the one that mounts it to the block or head? not the manifolds?

Thanks

TIMSPEED · 11-24-2003, 10:04 PM

Let me guess..you switched to headers and you can't figure out how to mount it right? Easy...
Just get a a 1/8" tubing, that's big enough to put the header bolt through, then cut it about 1¼" long, and get a longer header bolt...at least that's what I did...

soleeagle · 11-25-2003, 12:46 AM

76bonanza

Where are you located? I made a few of these brackets at work for the same thing. I think I have one left and if you would like it I will send it to you for just the cost of shipping. It bolts to the 2 top bolts on the head and to the outer adjusting bolt on the pump. The only bad thing is I didnt put enough adjustment in the slot on it so you will need to tighten down the bottom adjusting bolt then put in the top bolt. It looks good and clean when I installed mine. Just needs to be painted. If your interested e-mail me at soleeagle@svs.net

stan79chevy · 11-25-2003, 02:45 AM

Quote:

Originally posted by TIMSPEED
Let me guess..you switched to headers and you can't figure out how to mount it right? Easy...
Just get a a 1/8" tubing, that's big enough to put the header bolt through, then cut it about 1¼" long, and get a longer header bolt...at least that's what I did...

thats what i did too worked good

*1FaastC10* · 11-25-2003, 12:43 PM

my Edelbrock headers that i have on my TA actually came with little tubes, and loger header bolts. they work great.

11-24-2003, 08:48 PM	#1
76bonanza Senior Member Join Date: Mar 2003 Location: St robert Mo Posts: 2,001	power steering bracket Any one know where I can get a power steering upper mounting bracket the one that mounts it to the block or head? not the manifolds? Thanks __________________ 1968 c10 lowered 3" 4" 355/Th400 built by Hatfield racing in joplin MO

11-24-2003, 10:04 PM	#2
TIMSPEED Join Date: Jan 2003 Location: Modesto, CA Posts: 1,321	Let me guess..you switched to headers and you can't figure out how to mount it right? Easy... Just get a a 1/8" tubing, that's big enough to put the header bolt through, then cut it about 1¼" long, and get a longer header bolt...at least that's what I did... __________________ I have a few cars... See Them Here

11-25-2003, 12:46 AM	#3
soleeagle Registered User Join Date: Sep 2003 Location: Shelbyville, Indiana Posts: 614	76bonanza Where are you located? I made a few of these brackets at work for the same thing. I think I have one left and if you would like it I will send it to you for just the cost of shipping. It bolts to the 2 top bolts on the head and to the outer adjusting bolt on the pump. The only bad thing is I didnt put enough adjustment in the slot on it so you will need to tighten down the bottom adjusting bolt then put in the top bolt. It looks good and clean when I installed mine. Just needs to be painted. If your interested e-mail me at soleeagle@svs.net __________________ Chuck '85 Chevy Silverado 4X4 '91 Chevy 4X4 Suburban http://www.cardomain.com/memberpage/545941

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-25-2003, 12:43 PM	#5
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,399	my Edelbrock headers that i have on my TA actually came with little tubes, and loger header bolts. they work great.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.