|
06-05-2013, 01:25 PM
|
#1 |
|
Registered User
Join Date: Dec 2009
Location: McDonough,GA
Posts: 123
|
Sectioned crossmember
I'm going to section my crossmember soon. While I have been looking no one trims the front or rear edge (you know the little lip) just wanting y'all's ideas and thoughts of course it will be reinforced.
Posted via Mobile Device |
|
|
|
06-05-2013, 01:27 PM
|
#2 |
|
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Re: Sectioned crossmember
I think it should be fine to trim it but I would put a brace of some sort inside or out with L-profile or something like that.
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
|
|
|
|
06-11-2013, 02:41 PM
|
#3 |
|
Registered User
Join Date: Dec 2009
Location: McDonough,GA
Posts: 123
|
Re: Sectioned crossmember
had member sodablasted and have started sectioning
Posted via Mobile Device Posted via Mobile Device Posted via Mobile Device |
|
|
|
|
06-11-2013, 02:44 PM
|
#4 |
|
Registered User
Join Date: Dec 2009
Location: McDonough,GA
Posts: 123
|
Re: Sectioned crossmember
Posted via Mobile Device
Posted via Mobile Device |
|
|
|
|
06-11-2013, 09:22 PM
|
#5 |
|
Registered User
Join Date: Dec 2009
Location: McDonough,GA
Posts: 123
|
Re: Sectioned crossmember
Posted via Mobile Device
Posted via Mobile Device Posted via Mobile Device |
|
|
|
|
06-11-2013, 10:02 PM
|
#6 |
|
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Re: Sectioned crossmember
lookin good bud
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
|
|
|
|
06-11-2013, 11:02 PM
|
#7 |
|
Registered User
Join Date: Dec 2009
Location: McDonough,GA
Posts: 123
|
Re: Sectioned crossmember
I plan on doing just the mount locations at frame (with tack weld) then if all goes well burn them in and make a custom center out of plate steel. but of course kids job and wife come first. maybe they need to go on vacation without me haha.
|
|
|
|
|
06-12-2013, 06:13 AM
|
#8 |
|
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Re: Sectioned crossmember
LOL, I hear ya. Im in the same situation. Bout to go on a cruise and I'd rather be home working on my truck.
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
