|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-28-2013, 04:34 PM
|
#1 |
|
Registered User
 Join Date: Dec 2013
Location: Duluth, GA
Posts: 314
|
rad support carriage bolts
What was the purpose of using the 2 carriage bolts versus regular bolts? Having fun trying to remove them by myself with channel locks and my ratchet wrench -_- ...and can u get the bushing kit from parts stores or is it an order only item? Thanks
|
|
|
|
12-28-2013, 06:17 PM
|
#2 |
|
Senior Member
Join Date: Aug 2003
Location: Conyers,Ga.
Posts: 7,288
|
Re: rad support carriage bolts
Bushings order only not at local parts stores. Carriage works fine if you can keep it in square washer. 40 years usually messes that up.most tomes I just cut bolt.
|
|
|
|
|
12-28-2013, 10:35 PM
|
#3 |
|
Senior Member
Join Date: Aug 2008
Location: Cedar Park, Texas
Posts: 7,500
|
Re: rad support carriage bolts
Imo the factory originally used carriage bolts for easier/ quicker assembly. The carriage head would not require a wrench to tighten it all up. They werent concerned with you and i getting it apart 40 yrs later. I usually use the hot wrench and replace the bolts and bushin as a whole.
|
|
|
|
|
12-29-2013, 02:38 PM
|
#4 |
|
Registered User
Join Date: Dec 2013
Location: Duluth, GA
Posts: 314
|
Re: rad support carriage bolts
Lol you are right. Im just having a hard time getting the nuts off due to the tops spinning -_- any suggestions on best place (and price) for ordering a new rad support mount kit?
|
|
|
|
|
12-30-2013, 02:07 PM
|
#5 |
|
Registered User
Join Date: Jan 2013
Location: Rye Colorado
Posts: 43
|
Re: rad support carriage bolts
I usually tack weld the carriage bolt head to the square washer and it comes off or breaks
__________________
39 GMC pickup,70 GMC K1500 short bed 4x4 ,72 K10 short bed step side 4x4 ,71 short bed fleet side , 72 K20 long bed ,74 K10 long bed , 69 C30 dump bed dually, 79 K30 standard cab dually , 02 Dodge 4x4 dually |
|
|
|
|
02-17-2015, 09:41 PM
|
#6 |
|
Registered User
Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
Re: rad support carriage bolts
If someone were to replace those bolts with carriage bolts, what size are they please?
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
|
|
|
|
02-17-2015, 10:00 PM
|
#7 |
|
Registered User
Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
Re: rad support carriage bolts
To remove mine I was going to try and grab the shank of the bolt with needle nose vice grips, pray and loosen the nut.
Think it will work??
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
|
|
|
|
02-17-2015, 10:21 PM
|
#8 | |||
|
The Older Generation
  
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,772
|
Re: rad support carriage bolts
Quote:
Quote:
Quote:
Probably not, but good luck with it..... LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|||
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
