What did you do to your truck today part II. - Page 31 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

65CowboyCaddy · 06-09-2014, 01:03 PM

Drove it 600 miles on the HotRod power tour. The old 250 with T5 hung right in. Got over 20 MPG. Had a blast with her.

**pimpston65** · 06-09-2014, 02:03 PM

last coat of filler i used fiberglass first, then bondo to fill the pin holes. now sanding the whole cab with 80grit clean one last time tack rag it, then finally PRIMER. oh yeah!!!

**pimpston65** · 06-09-2014, 02:10 PM

making the patch panels disappear is a pain on ur back, the tilt is the way to go

**pimpston65** · 06-09-2014, 02:14 PM

so much filler only to sand 99% off, ugg

Grizz1963 · 06-09-2014, 04:07 PM

Another small safety related purchase today.

The existing mirrors were 5 inch round ones, tired, rusted and not very good as mirrors.

So I decided to go for the 5 X 7 inch rectangular ones so that I could see what was going on around me.

Another £28.00 out of the kitty. But a good spend in my view.

Also went to the Exhaust doctor to start investigating the full cost of a complete new stainless system, including a pair of cutouts.

Price quoted had me taste bile.

More homework.

mjh1965 · 06-09-2014, 04:58 PM

Quote:

Originally Posted by pimpston65

so much filler only to sand 99% off, ugg

Looking good have you got a build thread

vin63 · 06-09-2014, 05:06 PM

Finished the instrument cluster today...checking the high beam and turn signal indicator lenses i restored.

**pimpston65** · 06-09-2014, 05:42 PM

Quote:

Originally Posted by mjh1965

Looking good have you got a build thread

naw i started before smartphones, just polaroids so i figure why change now, i just post as i go. too busy building to take pics

**Chevy Fleetside** · 06-09-2014, 07:30 PM

Put plywood in the truck so now I can acually use it as one. Even made a cut out so I can get to my battery without climbing under the truck. All that work for something that is temporary. I guess you can tell how I get gas in the truck..

64shortbox · 06-09-2014, 08:23 PM

Not exactly today but over the last few weeks. I removed the rear springs & installed air bags with separate Schrader valves. I removed the home made receiver hitch that was welded on the truck and bought a used Reese receiver hitch off Craigslist for $30.00 - modified it, painted it & installed it. I wrapped the exhaust pipes with a fiberglass cloth where they passed near the air bags. I installed & wired a Curt brake controller ($55.00 off eBay). I finally hooked up the truck to our 28 foot travel trailer and took it for a jaunt around town. I was surprised how well the truck handled it but I didn't take it up any hills. Hills and rust haven't been invented yet out here in the central California. I still need to drop the stabilizer hitch down a notch or 2 but it's 109 degrees out here now and that's going to have to wait.
Tuesday morning the truck goes to the upholstery shop to get the front seat recovered.

robber grin · 06-10-2014, 06:04 AM

We discovered that the rear bumper for the 62 was actually 63 to 66 (duh) -so we had to figure out the mounting since I had it powder coated already.

I’m really "smart" like that.

Took some 1½” x ¼” mild steel bar stock and 1/2"-13 Grade 8 bolts & made adapters for the bumper mounting bolts.

Now we can still run the 60-62 brackets that we have on hand while mounting the 63-66 bumper that we had coated white.

rg & ray~ray

Ronw435 · 06-10-2014, 10:59 AM

Question? If you were going to partially restore a 65 C-10. Would you paint the frame and suspension parts. This truck will be my driver and will be taken on trips around the country. I don't have a sand blaster so will be scraping and wire brushing the frame before priming. Was wondering if anyone has used the industrial paints for the frame. I believe that was what was put on them from the factory right? BTW I have the body off the frame at this point.

Thanks for any responses.

Ron

**pimpston65** · 06-10-2014, 04:50 PM

hey if the cab is away from the frame,its a full on resto in my opinion. well today i did the final sanding before primer, if this beast aint clean after all these suds...

joesscamaro · 06-10-2014, 05:30 PM

Hey pimpston...mind me asking how you removed the old sound deadener off the bottom of your cab?

**pimpston65** · 06-10-2014, 06:15 PM

Quote:

Originally Posted by joesscamaro

Hey pimpston...mind me asking how you removed the old sound deadener off the bottom of your cab?

i used a putty knife til i rounded the edges and a cup style wire wheel, wasnt bad. im lie'n. cab sat outside for a few yrs rusted i sand blasted sat some more, then i had a guy blast it again then he prime'd it with some hellofa stuff, wasnt easy to even scuf with 80grit,but thats all behind me now...

TJ's Chevy · 06-10-2014, 06:27 PM

Drove it!

**jayoldschool** · 06-10-2014, 09:28 PM

New front brake lines, bled brakes. New rear shoes/combi, greased front end. Upper ball joints are still OEM, and tight! Repacked wheel bearings. Getting closer...

**pimpston65** · 06-10-2014, 10:03 PM

Quote:

Originally Posted by jayoldschool

New front brake lines, bled brakes. New rear shoes/combi, greased front end. Upper ball joints are still OEM, and tight! Repacked wheel bearings. Getting closer...

quick question, i installed the inner and outer bearings on the front spindle, i noticed they call for a inner bearing seal that goes on first, closest to the backing plate. dumb question is it needed? cuz i pounded like heck to get the inner bearing on, i guess i could use a puller to get em off if needs be...

**pimpston65** · 06-10-2014, 10:29 PM

hey Grizz1963 love that yellow seat cover, u should send it to me!!! glad you have a mate to help with things. now my cab hasnt been on the frame since 98'. so i hope yours doesnt take as long. if you thought it was fun taking it off the frame, bet you wet your nickers when its time to put it back on... keep up the good work.

markeb01 · 06-11-2014, 01:18 AM

Quote:

Originally Posted by 64shortbox

Not exactly today but over the last few weeks. I removed the rear springs & installed air bags with separate Schrader valves. I removed the home made receiver hitch that was welded on the truck and bought a used Reese receiver hitch off Craigslist for $30.00 - modified it, painted it & installed it. I wrapped the exhaust pipes with a fiberglass cloth where they passed near the air bags. I installed & wired a Curt brake controller ($55.00 off eBay). I finally hooked up the truck to our 28 foot travel trailer and took it for a jaunt around town. I was surprised how well the truck handled it but I didn't take it up any hills. Hills and rust haven't been invented yet out here in the central California. I still need to drop the stabilizer hitch down a notch or 2 but it's 109 degrees out here now and that's going to have to wait.
Tuesday morning the truck goes to the upholstery shop to get the front seat recovered.

Man that looks nice! The truck is beautiful and sure makes an attractive tow rig with the trailer attached. How do you like the manual air bags? Has it helped with trailer handling or braking? Also - do you have a build thread?

markeb01 · 06-11-2014, 01:19 AM

That cluster looks fantastic!

Quote:

Originally Posted by vin63

Finished the instrument cluster today...checking the high beam and turn signal indicator lenses i restored.

mjh1965 · 06-11-2014, 02:09 AM

Quote:

Originally Posted by pimpston65

hey Grizz1963 love that yellow seat cover, u should send it to me!!! glad you have a mate to help with things. now my cab hasnt been on the frame since 98'. so i hope yours doesnt take as long. if you thought it was fun taking it off the frame, bet you wet your nickers when its time to put it back on... keep up the good work.

Hi pimpstone it's actually my truck with the yellow seat cover the previous owner loved yellow . The chassis and the axel and dash were yellow as well .As for cab off if it goes on as easy as the removal I will be happy
Martin

My build thread. http://67-72chevytrucks.com/vboard/s...d.php?t=611614

BR3W CITY · 06-11-2014, 02:14 AM

Today, I hooked up a wideband, worked on my SD-tune, and grumbled about getting around to coating my bed.

**pimpston65** · 06-11-2014, 05:01 AM

Quote:

Originally Posted by mjh1965

Hi pimpstone it's actually my truck with the yellow seat cover the previous owner loved yellow . The chassis and the axel and dash were yellow as well .As for cab off if it goes on as easy as the removal I will be happy
Martin

My build thread. http://67-72chevytrucks.com/vboard/s...d.php?t=611614

sorry, wasnt sure about ownership. i sent a PM, just wanted a closeup pic of the exhaust hanger is all...

robber grin · 06-11-2014, 06:32 AM

Just recently I filled the nail holes in my old yellow pine with Clear two-part Epoxy and sanded it all down for some clear polyurethane...

Fabbed and welded up some 2 x 3" blocks on the cross sills...

Fabbed a 3" filler panel frame for rear sill gap out of 1" angle...

Because we're bringing our floor up inside the bed-box to avoid the cut out or tunnel for clearance at the pumpkin. (Hope to bag it one day if I can)

rg & ray~ray

06-09-2014, 01:03 PM	#751
65CowboyCaddy Registered User Join Date: Jan 2014 Location: Johnson City, Tn Posts: 11	Re: What did you do to your truck today part II. Drove it 600 miles on the HotRod power tour. The old 250 with T5 hung right in. Got over 20 MPG. Had a blast with her.

06-09-2014, 02:03 PM	#752
pimpston65 Senior Member Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: What did you do to your truck today part II. last coat of filler i used fiberglass first, then bondo to fill the pin holes. now sanding the whole cab with 80grit clean one last time tack rag it, then finally PRIMER. oh yeah!!! Attached Images

06-09-2014, 02:10 PM	#753
pimpston65 Senior Member Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: What did you do to your truck today part II. making the patch panels disappear is a pain on ur back, the tilt is the way to go Attached Images

06-09-2014, 02:14 PM	#754
pimpston65 Senior Member Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: What did you do to your truck today part II. so much filler only to sand 99% off, ugg Attached Images

06-09-2014, 04:07 PM	#755
Grizz1963 Registered User Join Date: Dec 2012 Location: Rochester, KENT Posts: 10,565	Re: What did you do to your truck today part II. Another small safety related purchase today. The existing mirrors were 5 inch round ones, tired, rusted and not very good as mirrors. So I decided to go for the 5 X 7 inch rectangular ones so that I could see what was going on around me. Another £28.00 out of the kitty. But a good spend in my view. Also went to the Exhaust doctor to start investigating the full cost of a complete new stainless system, including a pair of cutouts. Price quoted had me taste bile. More homework. __________________ MY BUILD LINK: http://67-72chevytrucks.com/vboard/s...585901]Redneck Express - 1966 C10 Short Fleetside MY USA ROADTRIPS http://forum.retro-rides.org/thread/...2018-humdinger IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM MATE.

06-09-2014, 05:06 PM	#757
vin63 It's Better With Nitro Join Date: Apr 2008 Location: Chino Hills, CA Posts: 2,262	Re: What did you do to your truck today part II. Finished the instrument cluster today...checking the high beam and turn signal indicator lenses i restored. __________________ 1963 C-10: Deluxe-optioned cab, shortbed, fleetside Pontiac 462 ci, Kauffman D-Port alum. heads 4L80E, narrowed sheetmetal Ford 9-inch Tubular front and rear suspension Custom 6-piston front disc and 4-piston rear disc brakes

06-09-2014, 07:30 PM	#759
Chevy Fleetside Registered User Join Date: Sep 2006 Location: San Francisco Posts: 4,781	Re: What did you do to your truck today part II. Put plywood in the truck so now I can acually use it as one. Even made a cut out so I can get to my battery without climbing under the truck. All that work for something that is temporary. I guess you can tell how I get gas in the truck.. Attached Images __________________ "A man and his truck, what a beautiful thing" 65 Short Fleetside BBC 65 Long Fleetside 283 3 on the tree for now. my build thread http://www.67-72chevytrucks.com/vboa...d.php?t=259536

06-09-2014, 08:23 PM	#760
64shortbox Registered User Join Date: Jan 2011 Location: Tulare, CA Posts: 733	Re: What did you do to your truck today part II. Not exactly today but over the last few weeks. I removed the rear springs & installed air bags with separate Schrader valves. I removed the home made receiver hitch that was welded on the truck and bought a used Reese receiver hitch off Craigslist for $30.00 - modified it, painted it & installed it. I wrapped the exhaust pipes with a fiberglass cloth where they passed near the air bags. I installed & wired a Curt brake controller ($55.00 off eBay). I finally hooked up the truck to our 28 foot travel trailer and took it for a jaunt around town. I was surprised how well the truck handled it but I didn't take it up any hills. Hills and rust haven't been invented yet out here in the central California. I still need to drop the stabilizer hitch down a notch or 2 but it's 109 degrees out here now and that's going to have to wait. Tuesday morning the truck goes to the upholstery shop to get the front seat recovered. Attached Images

06-10-2014, 06:04 AM	#761
robber grin Registered User Join Date: Apr 2012 Location: Sunny Youngwood PA Posts: 463	Re: What did you do to your truck today part II. We discovered that the rear bumper for the 62 was actually 63 to 66 (duh) -so we had to figure out the mounting since I had it powder coated already. I’m really "smart" like that. Took some 1½” x ¼” mild steel bar stock and 1/2"-13 Grade 8 bolts & made adapters for the bumper mounting bolts. Now we can still run the 60-62 brackets that we have on hand while mounting the 63-66 bumper that we had coated white. rg & ray~ray Attached Images

06-10-2014, 10:59 AM	#762
Ronw435 Registered User Join Date: Apr 2014 Location: Fate, Texas ( About 35 miles east of Dallas) Posts: 318	Re: What did you do to your truck today part II. Question? If you were going to partially restore a 65 C-10. Would you paint the frame and suspension parts. This truck will be my driver and will be taken on trips around the country. I don't have a sand blaster so will be scraping and wire brushing the frame before priming. Was wondering if anyone has used the industrial paints for the frame. I believe that was what was put on them from the factory right? BTW I have the body off the frame at this point. Thanks for any responses. Ron

06-10-2014, 04:50 PM	#763
pimpston65 Senior Member Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: What did you do to your truck today part II. hey if the cab is away from the frame,its a full on resto in my opinion. well today i did the final sanding before primer, if this beast aint clean after all these suds... Attached Images Last edited by pimpston65; 06-10-2014 at 05:08 PM.

06-10-2014, 05:30 PM	#764
joesscamaro Registered User Join Date: Sep 2008 Location: Newport, North Carolina Posts: 642	Re: What did you do to your truck today part II. Hey pimpston...mind me asking how you removed the old sound deadener off the bottom of your cab?

06-10-2014, 06:27 PM	#766
TJ's Chevy Registered User Join Date: Mar 2013 Location: Southern Oregon Posts: 10,384	Re: What did you do to your truck today part II. Drove it! __________________ 1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw

06-10-2014, 09:28 PM	#767
jayoldschool Moderator Join Date: Dec 2012 Location: ON, Canada Posts: 2,170	Re: What did you do to your truck today part II. New front brake lines, bled brakes. New rear shoes/combi, greased front end. Upper ball joints are still OEM, and tight! Repacked wheel bearings. Getting closer...

06-10-2014, 10:29 PM	#769
pimpston65 Senior Member Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: What did you do to your truck today part II. hey Grizz1963 love that yellow seat cover, u should send it to me!!! glad you have a mate to help with things. now my cab hasnt been on the frame since 98'. so i hope yours doesnt take as long. if you thought it was fun taking it off the frame, bet you wet your nickers when its time to put it back on... keep up the good work.



Register or Log In To remove these advertisements.

06-11-2014, 02:14 AM	#773
BR3W CITY meowMEOWmeowMEOW Join Date: Sep 2009 Location: MKE WI Posts: 7,128	Re: What did you do to your truck today part II. Today, I hooked up a wideband, worked on my SD-tune, and grumbled about getting around to coating my bed. __________________ *'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING* MY BUILD THE H8RDCPTR //\\ MY YOUTUBE CHANNEL REV J HD

06-11-2014, 06:32 AM	#775
robber grin Registered User Join Date: Apr 2012 Location: Sunny Youngwood PA Posts: 463	Re: What did you do to your truck today part II. Just recently I filled the nail holes in my old yellow pine with Clear two-part Epoxy and sanded it all down for some clear polyurethane... Fabbed and welded up some 2 x 3" blocks on the cross sills... Fabbed a 3" filler panel frame for rear sill gap out of 1" angle... Because we're bringing our floor up inside the bed-box to avoid the cut out or tunnel for clearance at the pumpkin. (Hope to bag it one day if I can) rg & ray~ray Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.