|
01-12-2004, 10:47 PM
|
#1 |
|
Tasty Cakes!
Join Date: Apr 2003
Location: Gilbert, AZ
Posts: 2,112
|
leaning truck
Hey guys,
I posted earlier about helping my friend remove some leafs from his truck. Well, with your help, we accomplished that feat. But now the front driver's side is one inch higher than the other corners. Could it be that all of the other springs have more give? Or is there something else amiss? I don't know the history of this truck (if it was wrecked or not). Should I just heat up that coil to bring it down? Help! 
__________________
I'm a little  and a lot  Ground beef: A cow with no legs. ---------------- '66 Chevy SWB "Penny" '67 Chevy Big Window SWB- aka "Pearl" '72 Burb- "Betty" "It's not a hearse dammit" '99 Chevy Ext. cab Silverado |
|
|
|
01-12-2004, 11:17 PM
|
#2 |
|
Robert Olson Transport
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,310
|
never heat coils it can be very dangerous. if you have spring problems switch out the whole set. mine leans too and thats what im doin to mine especially if youre a big gguy like me the springs ont he left seem to wear faster than theright one especially if the gas tank is on that side.. more weight on a side wears it out more
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
|
01-13-2004, 04:22 PM
|
#3 |
|
Insert Witty Text Here
Join Date: Oct 2002
Location: San Antonio, TX
Posts: 3,415
|
As has been pointed out before, if the truck is a 73-87, the gas tanks can cause it to lean one way or the other based on how much gas is in each tank.
When you measure, make sure you measure from the fender lip to the bottom of the wheel. That way, if the tires are not aired up evenly you still get a consistent measurement. All vehicles are off by a little bit, typically. You don't notice it until you start making changes to the suspension, then it becomes apparent. I measured mine last night, and the two sides are off by about 1/4 inch. EVERYTHING in the front suspension is new. Everything has zero miles on it except the springs, which have about 500 miles on them. Slonaker |
|
|
|
|
01-13-2004, 08:48 PM
|
#4 |
|
Registered User
Join Date: Jan 2004
Location: Oklahoma
Posts: 1,057
|
1/4 sounds pretty good to the 3 inches that my 85 swb was leaning when i bought it.
__________________
Youth soon passes away, but immaturity can last a life time. |
|
|
|
|
01-13-2004, 09:49 PM
|
#5 |
|
Insert Witty Text Here
Join Date: Oct 2002
Location: San Antonio, TX
Posts: 3,415
|
Certainly. My point was that, even with new parts, it still is not likely to be perfect.
I hope you got a good deal on it.  Slonaker |
|
|
|
|
01-14-2004, 11:09 AM
|
#6 | |
|
Registered User
Join Date: Dec 2002
Location: taylorsville, UT
Posts: 778
|
Quote:
I think you mean fender lip to center of hub to get a consistant measurement.
__________________
2011 CCSB GMC 2500HD DMAX 73 GMC 3/4 ton 4x4 96 Chevy 1500 STD Cab Shortbed Z71 Owner of WickedWolfRC.com |
|
|
|
|
|
01-14-2004, 11:52 AM
|
#7 |
|
Insert Witty Text Here
Join Date: Oct 2002
Location: San Antonio, TX
Posts: 3,415
|
The distance from the center of the hub to the bottom of my wheel never changes. Does yours?
Slonaker |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
)
Linear Mode
